|
[China]
Trade Verify
Address: No55. Jiucaiyuan road, Furong District, Changsha, Hunan,China
Contact name:Ling Bo
Changsha Sollroc Engineering Equipments Co., Ltd |
|
Verified Suppliers
|
|
|
High Drilling Efficiency Reverse Circulation SRC547 RC Rock Drill
Bits For Sampling
Product Introduce:
Reverse Circulation Drilling Rigs use a dual tube rod system, which
allows for a cost effective retrieval of the cuttings from the face
of the borehead to the surface by transporting them through the
inner tube, thus eliminating the need for sample retrieval by
tripping out or by the use of a wire line core barrel system.
Reverse Circulation drilling method gives a possibility to obtain
mineral samples in the early phases of a drilling project due to
the high speed and low cost.
Although, Reverse Circulation drilling samples provide slightly
less information regarding the formation, this shortage is largely
offset by significantly reduced cost of drilling and rapid
penetration rates. Sollroc's equipment offers the best choice of
quality reverse circulation drilling tools to satisfy any of your
drilling needs.
Specification:
SRC547 drill bit specification
| Drill bit shank | Bit diameter | Guage | Front | Center | Recommend shroud | weight (kg) |
| buttons | buttons | buttons |
| SRC547 | 133 | 8×φ16 | 6×φ14 | 3×φ14 | 131 | 16.9 |
| 135 | 8×φ16 | 6×φ16 | 3×φ14 | 133 | 17 | |
| 137 | 8×φ16 | 6×φ16 | 3×φ14 | 135 | 17.1 | |
| 140 | 8×φ16 | 6×φ16 | 3×φ14 | 138 | 17.2 | |
| 143 | 8×φ16 | 6×φ16 | 3×φ14 | 141 | 17.3 | |
| 146 | 8×φ16 | 6×φ16 | 3×φ14 | 144 | 17.6 |
SRC547 Hammer specification
| Length | Weight | External diameter | Bit hole range | Connect thread | Working pressure | Airpressure | ||
| 1.7Mpa | 2.4Mpa | 3Mpa | |||||||
| 1270mm | 71kgs | 124.5mm | 133-146mm | 4.5" Remet | 1.5-3.5Mpa | 16m³/min | 22m³/min | 28m³/min |
Adavantages:
1. High Drilling Efficiency
2. Giving sampling faster and more accurate
3. High ratio of actual drilling time/ preparing time
4. High quality well achieved
5. Lower drilling cost
6. Larger diameter hole can be drilled
Basics of Reverse Circulation Drilling:The drilling theory of air reverse circulation is similar with the
theory of drawing water with air compressor.
The air flows down the annulus between inner tube and outer tube
and go inside single wall pipe right at air water mixer, where
produces countless tiny bubbles. These bubbles going up along the
pipe and expanding simultaneously. Due to the air continuing going
inside the fluid, it formed lower density mixture of air and water
upper the mixer. It leads the higher density fluid in the well go
up with cuttings because of the pressure difference. In this way
the cuttings are brought out of the well hole very fast.
Photo:
About us:
SOLLROC Reverse Circulation drilling (RC) ,from size 3’’ to 5.5’’,
is a technique of drilling that uses dual wall drill rods that
consist of an outer drill rod with an inner tube. By using
compressed air to extract rock fragments sample,the samples travel
through rods to a sample splitter at surface, avoiding all contact
between the samples and the borehole wall that allows samples to be
retrieved with minimal contamination,which is mainly used in deep
hole exploration and mining grade control.
Delivery Way:
By Air, By express or By Sea
Package :
Ply-wooden cases + pallet
