Active Member
|
[China]
Address: No. 12, Chuangxing Road, Baisha, Humen Town, Dongguan, Guangdong, China
Contact name:Calin Deng
GUANGDONG RUIHUI INTELLIGENT TECHNOLOGY CO., LTD. |
|
|
The pneumatic feeder is the most affordable feeder in the stamping
industry, as it automates stamping production with minimal customer
investment.
1. Install the three-point combination before the air inlet of the
pneumatic feeder, and add a proper amount of lubricating oil to the
three-point combination oiler, then connect the air source and
adjust the screw on the three-point combination filter to adjust
the intake air. The pressure is such that the air pressure of the
pneumatic feeder is maintained at 4.5 kg/cm2 to 5 kg/cm2.
2. Open the air valve of the pneumatic feeder and let the airflow enter the pneumatic feeder. At this time,
check whether there are air leakage in each part of the pneumatic
feeder. If there is any air leakage, re-apply the waterproof tape
and tighten until there is no leakage. So far.
3. When the airflow enters the pneumatic feeder, the floating rod
will bounce up, and then press the floating rod down by hand, which
will make the moving splint of the pneumatic feeder slide, and
check whether the sliding is stable in time. At the same time,
observe whether the action of the fixed splint and the moving
splint are synchronized. When the fixed splint is required to be
clamped, the moving splint should be in a relaxed state.
4. Press the pneumatic feeder floating rod repeatedly. If the
moving slider hits the recoil pad, the speed of the feeder is very
fast. The feeding speed should be adjusted properly. At this time,
the speed of the machine can be adjusted by using the speed
adjusting screw. It is enough to make the running speed and the
punching speed consistent.
5. Finally, the air valve of the pneumatic feeder is closed, the
material to be fed is moved from the inlet to the moving splint and
the fixed splint, and then the gas source is turned on, and the
punch is started to check whether there is a bias in the feeding
process. Whether the speed can fully match the punch.
Specification:
| Model | MAC2-400 | MAC2-500 | MAC2-600 | MAC2-800 | ||
| Stock Width(mm) | 50-400 | 50-500 | 50-600 | 50-800 | ||
| Stock Thickness(mm) | 0.3~3.2 | 0.3-3.2 | 0.3-3.2 | -3.2 | ||
| Max.Coil Weight(kg) | 3000 | 3000 | 3000 | 5000 | 5000 | 7000 |
| Max.Coil O.D.(mm) | 1200 | 1200 | 1200 | |||
| Coil I.D.(mm) | 8 | 8 | 508 | 508 | ||
| Feed Length(mm) | ~500* | ~500* | ~500* | ~500* | ||
| Max. Line Speed(m/min) | 16-24 | 16-24 | 16-24 | 16-24 | ||
| Work Roll Number(pieces) | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | ||
| Feed Roll Number(set) | 1 | 1 | 1 | 1 | ||
| Main Motor(kw) | AC2.9 | AC2.9 | AC4.4 | AC4.4 | ||
| Mandrel Expansion | hydraulic | hydraulic | hydraulic | hydraulic | ||
| Reel Motor(kw) | 1.5 | 1.5 | 1.5 | 2.2 | 2.2 | 3.7 |
| Power(V) | 3 Phase 220V/380V/50HZ | |||||
| Operating Air(Mpa) | 0.49 | 0.49 | 0.49 | 0.49 | ||
Straigtening performance:
| tock Thicknees (mm) | Stock Width (mm) | |||
| 0.3 | 400 | 500 | 600 | 800 |
| 0.4 | ||||
| 0.6 | ||||
| 0.8 | ||||
| 1.0 | ||||
| 1.2 | ||||
| 1.4 | ||||
| 1.6 | 470 | 470 | ||
| 1.8 | 400 | 400 | ||
| 2.0 | 360 | 360 | ||
| 2.3 | 300 | 300 | 300 | 300 |
| 2.5 | 230 | 230 | 230 | 230 |
| 2.8 | 150 | 150 | 150 | 150 |
| 3.2 | 110 | 110 | 110 | 110 |
*1:(Pneumatic):Option in case of pneumatic mandrel expansion is
provi
