Active Member
|
[China]
Address: No. 12, Chuangxing Road, Baisha, Humen Town, Dongguan, Guangdong, China
Contact name:Calin Deng
GUANGDONG RUIHUI INTELLIGENT TECHNOLOGY CO., LTD. |
|
|
Roller feeder, coil precision stamping, Guangdong high-speed punching processing
The roller feeder is not only divided into a variety of models according to the width and step of the applicable material, but also has a low speed and a high speed according to the actual feeding speed. The maximum speed of the Ruihui low speed roller feeder can only reach 190. Times/min, mainly used with traditional punching machines, low-speed pneumatic precision punching machine for medium and low speed stamping processing, and high-speed roller feeders up to 600 times/min, mainly used with high-speed punching machines for medium and high speed stamping processing. produce.
Roller feeders operate at the same speed, whether low speed or high speed: they are mounted on the output shaft of the punch (crankshaft) through the eccentric disc, through the cross joint, the tie rod, the rocker arm and the output shaft. The reciprocating rotation of the feeding drum is controlled, and the feeding roller realizes the feeding of the feeding roller by rotating the clamping drum through the gear set.
At the same time, the entraining roller is adjusted by the eccentric rod and the gap between the feeding rollers to finely adjust the thickness of the material to be gripped, and the elastic tensioning spring can be used to appropriately press the clamping roller to press the feeding material, and the feeding roller reciprocally rotates the feeding, and then The inertia of the feed roller is damped by the brake device.
When feeding to the predetermined position, the roller feeder mounted on the punch slider relaxes the rod-spinning device to release the Palin at a proper time, and flips the relaxation shaft with the stepped shaft at both ends to lift the clamping roller to loosen the material to make the die The locating pin accurately aligns the material with the material.
Specification:
| Model | MAC2-400 | MAC2-500 | MAC2-600 | MAC2-800 | ||
| Stock Width(mm) | 50-400 | 50-500 | 50-600 | 50-800 | ||
| Stock Thickness(mm) | 0.3~3.2 | 0.3-3.2 | 0.3-3.2 | -3.2 | ||
| Max.Coil Weight(kg) | 3000 | 3000 | 3000 | 5000 | 5000 | 7000 |
| Max.Coil O.D.(mm) | 1200 | 1200 | 1200 | |||
| Coil I.D.(mm) | 8 | 8 | 508 | 508 | ||
| Feed Length(mm) | ~500* | ~500* | ~500* | ~500* | ||
| Max. Line Speed(m/min) | 16-24 | 16-24 | 16-24 | 16-24 | ||
| Work Roll Number(pieces) | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | ||
| Feed Roll Number(set) | 1 | 1 | 1 | 1 | ||
| Main Motor(kw) | AC2.9 | AC2.9 | AC4.4 | AC4.4 | ||
| Mandrel Expansion | hydraulic | hydraulic | hydraulic | hydraulic | ||
| Reel Motor(kw) | 1.5 | 1.5 | 1.5 | 2.2 | 2.2 | 3.7 |
| Power(V) | 3 Phase 220V/380V/50HZ | |||||
| Operating Air(Mpa) | 0.49 | 0.49 | 0.49 | 0.49 | ||
Straigtening performance:
| tock Thicknees (mm) | Stock Width (mm) | |||
| 0.3 | 400 | 500 | 600 | 800 |
| 0.4 | ||||
| 0.6 | ||||
| 0.8 | ||||
| 1.0 | ||||
| 1.2 | ||||
| 1.4 | ||||
| 1.6 | 470 | 470 | ||
| 1.8 | 400 | 400 | ||
| 2.0 | 360 | 360 | ||
| 2.3 | 300 | 300 | 300 | 300 |
| 2.5 | 230 | 230 | 230 | 230 |
| 2.8 | 150 | 150 | 150 | 150 |
| 3.2 | 110 | 110 | 110 | 110 |
*1:(Pneumatic):Option in case of pneumatic mandrel expansion is
provi
