Active Member
|
[China]
Address: No. 12, Chuangxing Road, Baisha, Humen Town, Dongguan, Guangdong, China
Contact name:Calin Deng
GUANGDONG RUIHUI INTELLIGENT TECHNOLOGY CO., LTD. |
|
|
s series type highspeed material coil feeder, NC feeder, stamping and feeding equipment
NC feeder is one of the three most commonly used feeders in stamping production. It uses electromechanical control to feed, but there is an obvious defect in electromechanical control.
That is, when the punch reaches a speed of 250 strokes per minute, the NC feeder can not accurately feed each punch.
Because the electromechanically controlled intermittent feeder reaches 250 strokes per minute, it means that the time per punch is only about 0.24 seconds, because the stamping stroke of the high-speed punch is only about 25mm to 30mm, and the mold is in the stamping process. The material is guided by the guiding pin. When the upper die and the lower die are matched, the protruding structure of the male die cannot be fed when contacting the material.
Therefore, when using high-speed punching machine for high-speed feeding, other types of feeding equipment are needed, and the gear feeding machine is the synchronous feeding device designed by Ruihui Machinery for high-speed feeding.
The gear feeder completely controls the various actions in the feeding process by means of mechanical linkage. Therefore, there is no response time problem in the movement of each part of the feeder, and the high-speed feeding does not need to worry about the feeding error caused by insufficient response time.
And the action of the key parts is the cam (the advantage of the cam is that the motion repeatability is good) and the mechanical linkage mode of the structure is controlled.
Therefore, the repeatability of the movement of the various components of the gear feeder during the feeding process is ensured, so that it can meet the progressive feeding requirements of various speeds and precisions, and can adapt to various speeds, various feeding specifications, and is particularly suitable for high-speed punching machines. Feeding needs.
Products:
Specification:
| Model | MAC2-400 | MAC2-500 | MAC2-600 | MAC2-800 | ||
| Stock Width(mm) | 50-400 | 50-500 | 50-600 | 50-800 | ||
| Stock Thickness(mm) | 0.3~3.2 | 0.3-3.2 | 0.3-3.2 | -3.2 | ||
| Max.Coil Weight(kg) | 3000 | 3000 | 3000 | 5000 | 5000 | 7000 |
| Max.Coil O.D.(mm) | 1200 | 1200 | 1200 | |||
| Coil I.D.(mm) | 8 | 8 | 508 | 508 | ||
| Feed Length(mm) | ~500* | ~500* | ~500* | ~500* | ||
| Max. Line Speed(m/min) | 16-24 | 16-24 | 16-24 | 16-24 | ||
| Work Roll Number(pieces) | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | ||
| Feed Roll Number(set) | 1 | 1 | 1 | 1 | ||
| Main Motor(kw) | AC2.9 | AC2.9 | AC4.4 | AC4.4 | ||
| Mandrel Expansion | hydraulic | hydraulic | hydraulic | hydraulic | ||
| Reel Motor(kw) | 1.5 | 1.5 | 1.5 | 2.2 | 2.2 | 3.7 |
| Power(V) | 3 Phase 220V/380V/50HZ | |||||
| Operating Air(Mpa) | 0.49 | 0.49 | 0.49 | 0.49 | ||
Straigtening performance:
| tock Thicknees (mm) | Stock Width (mm) | |||
| 0.3 | 400 | 500 | 600 | 800 |
| 0.4 | ||||
| 0.6 | ||||
| 0.8 | ||||
| 1.0 | ||||
| 1.2 | ||||
| 1.4 | ||||
| 1.6 | 470 | 470 | ||
| 1.8 | 400 | 400 | ||
| 2.0 | 360 | 360 | ||
| 2.3 | 300 | 300 | 300 | 300 |
| 2.5 | 230 | 230 | 230 | 230 |
| 2.8 | 150 | 150 | 150 | 150 |
| 3.2 | 110 | 110 | 110 | 110 |
*1:(Pneumatic):Option in case of pneumatic mandrel expansion is
provi
