Active Member
|
[China]
Address: No. 12, Chuangxing Road, Baisha, Humen Town, Dongguan, Guangdong, China
Contact name:Calin Deng
GUANGDONG RUIHUI INTELLIGENT TECHNOLOGY CO., LTD. |
|
|
Metal plate straightening machine, zigzag coil feeder, NC feeder
NC feeder failure analysis
Mechanical aspects:
(1) The NC feeder's rolling bearing is stuck and causes an alarm. The detection
method is: servo off, and then manually rotate the feeding roller
under no-load conditions. If there is obvious jam or unsmooth
phenomenon, it means the bearing is faulty.
The failure rate is also relatively low, generally does not appear,
if it occurs, the bearing must be replaced.
(2) After the customer replaces the mold, the height of the lower
mold is inconsistent with the height of the last mold or the length
of the positioning pin is inconsistent, which causes the relaxation
time to be delayed, causing the positioning pin to stretch the
material and alarming. This probability is large.
The detection method is: manual control of the slow decline of the
punch, careful observation of the drum relaxation time, repeated
detection, that is, the problem can be found. Solution: Adjust the
relaxation time; reduce the NCF feed height to be flush with the
mold or about 3mm lower.
(3) If the material is replaced, the thicker material is used, and
then the limit block is added in front, which may also cause an
alarm phenomenon. The probability is small and it is not easy to
appear, and the customer can find it by himself.
Products:
Specification:
| Model | MAC2-400 | MAC2-500 | MAC2-600 | MAC2-800 | ||
| Stock Width(mm) | 50-400 | 50-500 | 50-600 | 50-800 | ||
| Stock Thickness(mm) | 0.3~3.2 | 0.3-3.2 | 0.3-3.2 | -3.2 | ||
| Max.Coil Weight(kg) | 3000 | 3000 | 3000 | 5000 | 5000 | 7000 |
| Max.Coil O.D.(mm) | 1200 | 1200 | 1200 | |||
| Coil I.D.(mm) | 8 | 8 | 508 | 508 | ||
| Feed Length(mm) | ~500* | ~500* | ~500* | ~500* | ||
| Max. Line Speed(m/min) | 16-24 | 16-24 | 16-24 | 16-24 | ||
| Work Roll Number(pieces) | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | ||
| Feed Roll Number(set) | 1 | 1 | 1 | 1 | ||
| Main Motor(kw) | AC2.9 | AC2.9 | AC4.4 | AC4.4 | ||
| Mandrel Expansion | hydraulic | hydraulic | hydraulic | hydraulic | ||
| Reel Motor(kw) | 1.5 | 1.5 | 1.5 | 2.2 | 2.2 | 3.7 |
| Power(V) | 3 Phase 220V/380V/50HZ | |||||
| Operating Air(Mpa) | 0.49 | 0.49 | 0.49 | 0.49 | ||
Straigtening performance:
| tock Thicknees (mm) | Stock Width (mm) | |||
| 0.3 | 400 | 500 | 600 | 800 |
| 0.4 | ||||
| 0.6 | ||||
| 0.8 | ||||
| 1.0 | ||||
| 1.2 | ||||
| 1.4 | ||||
| 1.6 | 470 | 470 | ||
| 1.8 | 400 | 400 | ||
| 2.0 | 360 | 360 | ||
| 2.3 | 300 | 300 | 300 | 300 |
| 2.5 | 230 | 230 | 230 | 230 |
| 2.8 | 150 | 150 | 150 | 150 |
| 3.2 | 110 | 110 | 110 | 110 |
*1:(Pneumatic):Option in case of pneumatic mandrel expansion is
provi
