11.1V12.6V14.8V16.8V Enhance Balance BMS For Drill
Motor Lithium Battery Charger Protection Board 3S 4S 40A 60A
Product Description:
3 string 12.6V 40A lithium battery protection board
- Charging voltage: DC 12.6V~13.6V
- Continuous discharge current: 40A maximum (if the heat dissipation
environment is not good, please reduce the load current)
- Continuous charging current: up to 20A
- Balance Version size: 41x61x4mm
- Enhance Version size: 41x55x4mm
- Applicable choice: applicable to the nominal voltage of 3.7V, fully
charged 4.2V lithium battery (including 18650, 26650, polymer
lithium battery), can be drilled below 170W
Notes:
- Successfully start the drill requires 3 10C-20C power batteries, or
6 5C-10C power batteries (recommended power battery models: sony
vtc4, vtc4A, vtc5A, vtc6) OV and 12.6V cable, use Copper wire of 3
square millimeters or more (nickel sheets cannot be used)
- Strictly connect 0V, 4.2V, 8.4V, 12.6V according to the diagram. Do
not touch any components on the board when soldering the wire. Do
not intentionally short circuit.
- When soldering the battery for the first time or when charging is
in progress, as long as the single battery exceeds 4.2V, the "430"
resistor will heat up and discharge (discharge to about 4.19V to
stop heating). If the "430" resistor is severely hot, check if the
wrong line is connected.
Hardware preparation:
Prepare 3S 12.6V 40A lithium battery protection module,
battery, power supply, high power load resistor
![](http://img.everychina.com/nimg/9e/52/13b4998592271909a6c3d62c68b0.jpg)
The figure below shows the module discharge diagram. The battery is
3 strings. The connected battery needs to meet the 40A discharge
current. It can be realized by paralleling the battery or
purchasing a battery with a large discharge current. For example,
if the battery is 2000mAH and the discharge multiple is 10C, then
only 3 strings of 2 are needed and the discharge current is 40A.
![](http://img.everychina.com/nimg/05/2e/f8d8acad0fe354181a10bda7f594.jpg)
The figure below shows the battery charging diagram. The charging
voltage is DC12.6V~13.6V. The charging current depends on the
battery connected, and the maximum is no more than 20A. The module
has a balanced charging path, and the equalization function works
only when the battery performance is not much different.
![](http://img.everychina.com/nimg/99/e9/7e22f22e76bd9f1d90a6d8d0828b.jpg)
![](http://img.everychina.com/nimg/87/2d/a393c7740266e0eda592f27bd727.jpg)
4 string 14.8V 16.8V 40A lithium battery protection board
- Charging voltage: DC 16.8V~17V
- Continuous discharge current: 40A maximum (if the heat dissipation
environment is not good, please reduce the load current)
- Continuous charging current: up to 20A
- Balance Version size: 45x60x4mm
- Enhance Version size: 44x55x4mm
- Applicable choice: applicable to the nominal voltage of 3.7V, fully
charged 4.2V lithium battery (including 18650, 26650, polymer
lithium battery), can be drilled below 170W
Notes:
- The successful start of the drill requires three 15C-20C
power battery, or six 10C-15C power battery (ordinary 18650 can not
start the drill!!).
- strictly according to map wiring 0V, 4.2V, 8.4V, 12.6V,
16.8V, do not deliberately short circuit.
- When the load of the brush motor is used, try to connect a
non-polar capacitor (withstand voltage above 25V, capacity
10uF-100uF) to the motor's positive and negative terminals to
prevent the reverse spike from the motor. Break the MOS tube.
- 4 groups of batteries in series, please ensure that the voltage of
each group of batteries, if not the same, please fill each battery
separately and then use in series. The The Discharge test, the
voltage drop faster battery that group is poor battery.
The figure below shows the module discharge diagram. The battery is
4 strings. The connected battery needs to meet the 40A discharge
current. It can be realized by paralleling the battery or
purchasing a battery with a large discharge current. For example,
the battery 2000mAH, the discharge multiple 10C, then only need 4
series 2 and the maximum current can reach the discharge current
40A, stable discharge requires 4 strings 4 and can be, and need to
pay attention to heat dissipation, the discharge battery power will
drop rapidly.
![](http://img.everychina.com/nimg/60/aa/b574fb9d8851d54407d57d80c064.jpg)
![](http://img.everychina.com/nimg/8f/95/d0f9bf1971a1d9b13b9cb3dc00ec.jpg)
The picture below shows the battery charging diagram, 4 series of
batteries, the actual full charge, voltage 16.8V, charging voltage
DC17V-18V, charging current depends on the battery connected, the
maximum does not exceed 20A.
![](http://img.everychina.com/nimg/e7/53/0ca8b1f6cd380c6c6b78c129780e.jpg)