Home Companies Anping yuanfengrun net products Co., Ltd

Stainless Steel Brick Reinforcement Mesh

Contact Us

[China]

Trade Verify

Address: 5 Building, 9 Area, East Development Zone, Anping, Hebei P.R. China.

Contact name:Victor Meng

Anping yuanfengrun net products Co., Ltd

Verified Suppliers

Trust
Seal
Verified
Supplier
Credit
Check
Capability
Assessment

Stainless Steel Brick Reinforcement Mesh

Country/Region	china
City & Province	hebei
Categories	Metal Building Materials

Product Details

ASTM 580 Standard 9 Gauge Wire Diameter 4" Width Masonry Reinforcement Mesh

Masonry Reinforcement Mesh Introduction:

Masonry ladder&truss type reinforcement mesh Raw material:low carbon steel wire,stainless steel wire

The mesh can be electro galvanized or hot dip galvanized after welding,it mainly have two type,ladder type and truss type.

The wire diameter is from2.5mm to 6mm.

Brick Wall Reinforced Mesh, Used in Building Surface, Wall, Ground and Bridge.

Customized specifications and sizes are accepted.

Masonry Reinforcement Mesh is a prefabricated reinforcement for embedment in the horizontal mortar joints of masonry.

It is manufactured in 10′ 8″ lengths from wire conforming to ASTM A 82 / A82M for cold drawn steel wire.

It consists of two or more parallel and deformed longitudinal wires welded to a perpendicular cross wire spaced 16″ O.C. Out-to-out spacing is approximately two inches less than the nominal thickness of the wall.

MATERIAL : Iron wire & stainless steel wire 304/316
Qijie metal joint reinforcement products conform to:
ASTM A951 (Standard Specification for Steel Wire for Masonry
Joint Reinforcement)
Our products pass the testing of ASTM A951,We tested in USA .
Tensile Strength - 80,000 p.s.i. | Yield Point - 70,000 p.s.i. minimum
Zinc Coating:
Mill Galvanized coating: (0.1 oz/ft²)
Hot-Dip Galvanized after fabrication: (1.5 oz/ft²)
Wire Diameter:
9 gauge or 3/16”Ø
Side Rods and Cross Rods available in any combination of the above.
Cross Rods welded 16” O.C.
Block Size: Standard Sizes: 4” wall - 16“ wall.
Other widths available on special request.

Masonry Reinforcement Mesh Standard Specification:

* 4” wall - 16” wall
* Other widths available on special request
* (S) Standard: 9 ga. side rods x 9 ga. cross rods
* (EH) Extra Heavy: 3/16” side rods x 9 ga. cross rods
* (SHD) Super Heavy Duty: 3/16” side rods x 3/16” cross rods

Tensile Strength - 80,000 psi
Yield Point - 70,000 psi

ITEMS #	Block width	Mesh width	Weight(KGS)	PACKING
QJM2	4''	2''	0.57	50PCS/BDL,20BDL/PALLET
QJM4	6''	4''	0.61	50PCS/BDL,20BDL/PALLET
QJM6	8''	6''	0.64	50PCS/BDL,20BDL/PALLET
QJM8	10''	8''	0.68	50PCS/BDL,20BDL/PALLET
QJM10	12''	10''	0.71	50PCS/BDL,20BDL/PALLET

Standard Length	Width	Finishes
10’(3.05m)	2”(50mm)	Uncoated Electro Galvanized Hot Dipped Galvanized After Fabrication Stainless Steel
	4”(100mm)
	6”(150mm)
	8”(200mm)
	10”(250mm)
All products conform to: ASTM A641 - (Electro galvanized ) ASTM A153 Class B2 - (Hot dipped after fabrication) ASTM A 82 - (Cold drawn steel wire) Tensile Strength:80,000 PSI;Yield Point:70,000 PSI minimum;Reduction of Area:30 %. ASTM A951-96 - (Masonry wall reinforcing) ASTM 580 Type 304 - (Stainless steel)

Truss Type Block Reinforcement Mesh Specification

Reference	Width (mm)	Thickness (mm)	Length (mm)	Material
TM 50 S	50	3/4/5	3000	Galvanised steel
TM 100 GS	100	3/4/5	3000	Galvanised Steel
TM 150 GS	150	3/4/5	3000	Galavanised Steel
TM 200 GS	200	3/4/5	3000	Galavanised steel
TM 50 SS	50	3/4/5	3000	Stainless steel
TM 100 SS	100	3/4/5	3000	Stainless steel
TM 150 SS	150	3/4/5	3000	Stainless steel
TM 200 SS	200	3/4/5	3000	Stainless Steel

Ladder Type Block Reinforcement Mesh Specification

Reference	Width (mm)	Thickness (mm)	Length (mm)	Material
LM 50 GS	50	3/4/5	3000	Galvanised steel
LM100 GS	100	3/4/5	3000	Galvanised steel
LM 150 GS	150	3/4/5	3000	Galvanised steel
LM 200 GS	200	3/4/5	3000	Galvanised Steel
LM 50 SS	50	3/4/5	3000	Stainless steel
LM 100 SS	100	3/4/5	3000	Stainless Steel
LM 150 SS	150	3/4/5	3000	Stainless steel
LM 200 SS	200	3/4/5	3000	Stainless Steel

Masonry Reinforcement Mesh Feature :

* Greatly reduces cracking that can arise from thermal stresses. This enhances resistance to water penetration, as cracks are controlled.

* Increases lateral flexural strength.

* Bonds exterior and interior masonry wythes together in composite or cavity walls. Also bonds masonry at intersecting walls and corners

* Increases elasticity and performance of masonry walls under various stresses

(1)Light in weight ,high intensity, huge loading capacity as well as good anti-earthquake capacity.

(2)Simple in construction operation, easy to install.

(3)Can act as a part of the structure of weight bearing, to reduce the cost of material.

(4)Put the panel above the welded wire net fill cement between them.

(5)This type of floor decking sheet has the strong friction between the concrete and floor slab, being fire resistant.

(6)This deck is connected with steel bar ,making it have the higher strength.

Masonry Reinforcement Mesh Application:

Concrete slabbing, roads, paving, foundations, marine work, bank strong rooms, partition slabs, concrete block work, asphalt guttering and so on

1. steel truss applied to precast slabs, pre-high-speed railway sleeper.

2. Used in many high-rise, ultra- high-rise steel buildings

3. Used for steel building, mezzanine floor of “LOFT”

4. The force applied to the complex, special-shaped structure, building

5. Used in-situ concrete structure(RC) buildings

6. Used in the construction of slope roof structure

Hot Products

Black Powder Coated Metal Tubular Fencing 1.8m High 2.4m Width Commercial

Akzo Nobel Black Powder Coated 1.8m High 2.4m Width Commercial Tubular Fencing Tubular Fencing ...

Astm F2589 Standard Decorative Wrought Iron Fence Anti Rust Border Protection

ASTM F2589 Standard Anti Rust Easily Assembled Border Protection Wrought Iron Fence Wrought Iron ...

5x8ft Ornamental Metal Fencing Pre Galvanized With Powder Coated Full Welding Eco Friendly

Pre Galvanized With Powder Coated Full Welding Eco Friendly Ornamental Fence Ornamental Fence ...

School 2000mm High Picket Vinyl Fence Spear Top Type 2400mm Length Vinyl Coated

School 2000mm High Spear Top Type 2400mm Length Vinyl Coated Picket Vinyl Fence Picket Vinyl Fence ...

Military Bases Cross Resistance Ornamental Garden Gates Black Color Vinyl Coated 3.0m High

Military Bases Cross Resistance Black Color Vinyl Coated 3.0m High Ornamental Gate Ornamental Gate ...

A36 Material Security Metal Fencing Astm F2589 Standard Pvc Coated 2m High

A36 Material ASTM F2589 Standard PVC Coated High Security Metal Fencing Security Metal Fencing ...

Related Products

Stainless Steel Brick Reinforcement Mesh

Contact Us

Anping yuanfengrun net products Co., Ltd

Stainless Steel Brick Reinforcement Mesh

Product Details

ASTM 580 Standard 9 Gauge Wire Diameter 4" Width Masonry Reinforcement Mesh

Masonry Reinforcement Mesh Introduction:

Masonry ladder&truss type reinforcement mesh Raw material:low carbon steel wire,stainless steel wire

The mesh can be electro galvanized or hot dip galvanized after welding,it mainly have two type,ladder type and truss type.

The wire diameter is from2.5mm to 6mm.Brick Wall Reinforced Mesh, Used in Building Surface, Wall, Ground and Bridge.Customized specifications and sizes are accepted.

Masonry Reinforcement Mesh is a prefabricated reinforcement for embedment in the horizontal mortar joints of masonry.

It is manufactured in 10′ 8″ lengths from wire conforming to ASTM A 82 / A82M for cold drawn steel wire.

It consists of two or more parallel and deformed longitudinal wires welded to a perpendicular cross wire spaced 16″ O.C. Out-to-out spacing is approximately two inches less than the nominal thickness of the wall.

Masonry Reinforcement Mesh Standard Specification:

* 4” wall - 16” wall* Other widths available on special request* (S) Standard: 9 ga. side rods x 9 ga. cross rods* (EH) Extra Heavy: 3/16” side rods x 9 ga. cross rods* (SHD) Super Heavy Duty: 3/16” side rods x 3/16” cross rods

*Tensile Strength - 80,000 psi*Yield Point - 70,000 psi

ITEMS #

Block width

Mesh width

Weight(KGS)

PACKING

QJM2

4''

2''

0.57

50PCS/BDL,20BDL/PALLET

QJM4

6''

4''

0.61

50PCS/BDL,20BDL/PALLET

QJM6

8''

6''

0.64

50PCS/BDL,20BDL/PALLET

QJM8

10''

8''

0.68

50PCS/BDL,20BDL/PALLET

QJM10

12''

10''

0.71

50PCS/BDL,20BDL/PALLET

Standard Length

Width

Finishes

10’(3.05m)

2”(50mm)

Uncoated

Electro Galvanized

Hot Dipped Galvanized After Fabrication

Stainless Steel

4”(100mm)

6”(150mm)

8”(200mm)

10”(250mm)

Truss Type Block Reinforcement Mesh Specification

Reference

Width (mm)

Thickness (mm)

Length (mm)

Material

TM 50 S

50

3/4/5

3000

Galvanised steel

TM 100 GS

100

3/4/5

3000

Galvanised Steel

TM 150 GS

150

3/4/5

3000

Galavanised Steel

The wire diameter is from2.5mm to 6mm.

Brick Wall Reinforced Mesh, Used in Building Surface, Wall, Ground and Bridge.

Customized specifications and sizes are accepted.

* 4” wall - 16” wall
* Other widths available on special request
* (S) Standard: 9 ga. side rods x 9 ga. cross rods
* (EH) Extra Heavy: 3/16” side rods x 9 ga. cross rods
* (SHD) Super Heavy Duty: 3/16” side rods x 3/16” cross rods

Tensile Strength - 80,000 psi
Yield Point - 70,000 psi