Active Member
|
[China]
Address: 1ST FLOOR, UNIT 1, NO.9 GUANSHAN ROAD, FENGDU INDUSTRIAL PARK, PINGYAO, YUHANG, HANGZHOU, ZHEJIANG
Contact name:Colin Mao
ZHEJIANG XINCHOR TECHNOLOGY CO., LTD. |
|
|
3:1 Fast Cure Modified Pure Epoxy Injectable Anchor Adhesive
Chemical anchor adhesive, epoxy injection mortar, Chemical fixing glue,
Chemical anchoring system used for anchoring and rebar connections in concrete.
Strong, Versatile Epoxy Anchor Adhesives For Threaded Rod, Rebar
Item #: FixingChor139
Capacity: 390ml
Materials: Epoxy
Mixing Ratio: 3:1
Product Description:
3:1 Fast Cure Modified Pure Epoxy Injectable Anchor Adhesive
with approvals for rebar connections and heavy-duty anchoring
Base material condition: Dry, Wet
Base materials: Concrete (cracked and uncracked), Masonry wall
Application Range
Fixing of handrails, balustrades and supports
Fixing of railings
Fixing of window and door frames
For structural work:
Rebar / steel reinforcement anchoring in new and refurbishment works.
Threaded rods
Bolts and special fastening systems
Mechanical and electrical services installation
Anchoring of supports for ducting and equipment.
Metal Work, carpentry
Fixing of the following substrates:
Suitable for
Non-cracked concrete
Reinforcement bars
Concrete
Hard natural and reconstituted stone
Solid rock and masonry
For fixing of:
Steel constructions
Staircases
Consoles
Machines
High-racks
Wooden constructions
Reinforcement bars
Technical Parameter:
1. Basic parameters
1) Appearence
Part A (main): white cream
Part B (hardener): red cream / grey cream
2) Mixed Viscosity: 18-22Pa.s
3) Hardened density: 1.50±0.10g/cm3
4) Mixing ratio (Volume ratio): 390ml(3:1)
5) Shelf time: 24 months
2 Main Performance
| Testing project | Condition | Index | ||
| Gel Performance (According to China National Standard GB50728-2011) | ||||
| Split Tensile Strength (MPa) | Under (23±2)℃, (50±5)%RH, tested by loading speed of 2mm/min | ≥8.5 | ||
| Flexural Strength (MPa) | ≥50 (no fragment damage) | |||
| Compressive Strength (MPa) | ≥60 | |||
| Bonding Capacity (According to China National Standard GB50728-2011) | ||||
| Steel-Steel Tensile Shear Strength (MPa) | (23±2)℃ (50±5)%RH | ≥10 | ||
| Bonding strength of Ribbed steel bar (or screw) with concrete under constrain drawing condition | (23±2)℃ (50±5)%RH | C30,Ф25,L=150mm | ≥11 | |
| C60,Ф25,L=150mm | ≥17 | |||
| Steel-Steel T-peeling strength (mm) | (23±2)℃,(50±5)%RH | ≤25 | ||
| Non-volatile content | (105±2)℃,(180±5)min | ≥99% | ||
| Ageing resistance to heat and humidity 90d | ||||
| Reduction rate of tensile strength | Under normal room temperature | ≤12% | ||
| (According to China National Standard JGJ145-2013) | ||||
| Tensile Strength (after high temperature welding) | Dia12 Grade II steel, C30 concrete Hole dia.16mm, Depth: 150mm | 55.1N, 57.0N, 54.8N | ||
3 Technical Data
Anchoring Adhesive used with thread rod
| Thread Rod Dia |
C30 Concrete | M10 | M12 | M16 | M20 | M24 |
| Drilling Dia.(mm) | 12 | 14 | 18 | 24 | 28 | |
| Depth (mm) | 90 | 110 | 145 | 180 | 220 | |
| Damage Pulling force KN | Grade 5.8 Steel | 29 | 42.2 | 78.5 | 122.5 | 254.5 |
| Grade 8.8 Steel / A4 SS | 36.8 | 52.9 | 94.1 | 147.0 | 211.7 | |
| Damage Cutting force KN | Grade 5.8 Steel | 17.4 | 25.3 | 47.1 | 73.5 | 105.9 |
| Grade 8.8 Steel | `27.8 | 40.5 | 75.3 | 117.6 | 169.4 | |
| Designed Pulling force KN | 12.0 | 17.02 | 30.6 | 52.4 | 75.2 | |
| Designed Cutting Force KN | Grade 5.8 Steel | 12.2 | 17.6 | 32.9 | 51.5 | 74.1 |
| Grade 8.8 Steel | 18.6 | 27.0 | 50.2 | 78.4 | 113.0 | |
| Holes for each | 54 | 25 | 8 | 5 | 3 |
Processing Method
1 Tools
2 Attention
Drilling: As per technical data sheet
Cleaning: using air pump or compressed air and brush to clean the holes completely.
Assembling and Injection: Mount the static mixer onto the bottle, push out some incomplete mixed gel at the front part,then inject from the bottom of the hole, to fill 1/2 to 2/3 depth of the hole.
Bar planting: spin slowly the rebar or thread rods into the hole, adjust up and down for several times to make the gel average, but don’t touch it during hardening time.
Curing and Maintenance: According to the temperature of the base materials, give enough time to harden and start to load mounting until it hardened completely.
Curing time:
| Operation and Curing time | |||||
| Temperarure ℃ | -5 | 0 | 10 | 20 | ≥30 |
| Operation time (min) | 60 | 45 | 30 | 25 | 20 |
| Curing time (h) | 72 | 48 | 24 | 12 | 6 |
Consumption Chart (holes per cartridge)
| Anchor Rod dia. | M10 | M12 | M16 | M20 | M24 |
| Drilling Dia.(mm) | 12 | 14 | 18 | 24 | 28 |
| Depth (mm) | 90 | 110 | 145 | 180 | 220 |
| Each usage | 8ml | 13ml | 28ml | 62ml | 103ml |
| 360ml | 45 | 27 | |||
| 390ml | 48 | 30 | 14 | 6 | 3 |
| 585ml | 73 | 45 | 20 | 9 | 5 |
| 650ml | 81 | 50 | 23 | 10 | 6 |
Our Product Lines:
- Carbon Fiber Reinforcement System: XQ-CFC 300gsm, 200gsm fabric and adhesives XQ-XW
- Steel Bonding System: XQ-GZ Epoxy grouting adhesives, XQ-JGN Plate bonding Adhesives
- Crack Repairing System: XQ-GF Crack grouting adhesives, XQ-FF crack seal adhesives
- Chemical Anchoring 390ml(3:1), 585ml(3:1), 650ml(1:1),
Our History:
15 years from 2000, ISO9001 approved, 40 employees, 5000m2 plant
Our Quality
All passed China National Standard lab testing, and be similar to CE and other countries standards
Our main product series:
-- Chemical Anchor series
Pure Epoxy Adhesive 360ml (5:1) 390ml(3:1) 585ml (3:1)
-- Carbon fiber reinforcement system,
XQ-XW carbon fiber epoxy adhesive
XQ-XB concrete surface leveling epoxy adhesive
XQ-CFC carbon fiber fabric 12K unidirectional 200gsm-600gsm
-- Steel bonding reinforcement system
XQ-JGN structural epoxy adhesive
XQ-GZ Grouting epoxy adhesive
XQ-FB edge sealing adhesive
-- Concrete repair system
XQ-GF crack grouting adhesive
XQ-FF crack sealing adhesive
