10KG Automotive Ac Recovery Machine Semi Automatic

10KG AC Recovery Machine Semi-automatic With Online Support

Refrigerant Recovery Procedure

Using a recovery/recycling machine is not difficult. The basic procedure goes as follows:

1. Connect the hoses on the recovery machine to the service fitting on the vehicle.

2. Turn the recovery unit on following the equipment manufacturer's operating instructions. Allow the machine to continue pulling refrigerant from the system until it indicates all of the refrigerant has been recovered (system pressure reads vacuum and holds vacuum for at least 5 minutes). If the machine does not have an automatic timer or shut-off, discontinue recovery at this time, and close and disconnect the service hoses.

TIP: If A/C components show evidence of icing during the recovery process, the components can be gently heated to speed up the flow of refrigerant. Use a hot air blow dryer, never any type of open flame, to heat parts.

3. Once the recovery process is complete, determine how much oil was pulled out along with the refrigerant so you can replace it when the system is recharged. Most machines have an oil cup that will show how much oil was taken out. The cup should usually have about one ounce of oil in it if the system contains the proper amount of oil. If the system is low on oil, there may be little or no oil in the cup. On the other hand, if the system is overcharged with oil, there may be several ounces of oil in the cup.

4. After the refrigerant has been recovered, the recycling process can begin. The time it takes to clean the refrigerant can vary from 20 minutes up to an hour depending on the amount of contamination. During the recycling phase, the refrigerant is filtered and dried. Particulates, moisture, oil and air are all removed until the refrigerant meets purity standards. A moisture indicator light usually signals when the job is done. The refrigerant can then be put back into the vehicle, or saved and reused in another vehicle.

Most machines use "single-pass" recycling where the refrigerant makes only one pass through the cleaning circuit, but some machines also offer "multi-pass" recycling or a choice of single-pass or multi-pass cleaning. Multi-pass cleaning takes longer but may be necessary with refrigerant that contains a lot of moisture.

The filter-drier that removes particulates and moisture from the refrigerant needs to be replaced periodically. Filter capacities vary somewhat from one machine to another, and lifespan depends on how much crud and moisture the filter picks up from the refrigerant. But as a rule, a typical filter will usually clean about 1,000 lbs . of refrigerant before it has to be replaced .

Description of 10KG AC Recovery Machine :

• Refrigerant recovery : rely on the machine’s internal system filtering device to recover the refrigerant into the work tank.
• Refrigerant recycle : separating refrigerant oil and moisture in air conditioning system to reach the reuse standards and ensure the purity of refrigerant so the refrigerant can be recycled.
• Refrigerant charging : refrigerant supplementary injecting setting , adding the appropriate amount of refrigerant to the vehicle.
• Leakage test : leakage test on the air conditioning pipe , ensure a good seal .
• Vacuuming : vacuum air - conditioning and equipment pipe .
• Refrigerant oil recharge : add refrigerant oil to the air-conditioning system .
• It adopts unique automatic protection design to prevent liquid attack and ultra high pressure explosion .
• With bigger cylinder .
• With fan condenser .

Parameter of 10KG AC Recovery Machine

Product features of 10KG AC Recovery Machine

• R134A Refrigerant Recovery Recycling Recharging Machine
• This machine model number is x520, it is Semi automatic.It has all the basic functions, like recovery , recycle , vacuum , recharging to AUTOMOBILE A / C system, drain waste oil .
• Recovery : Recovery refrigerant automatically , and the refrigerant meet the SAE standard .
• Charge : Charge refrigerant into the the perfectly sealed air condition system .
• Manual operation to purge the waste compressor oil and charge the new oil .
• Vacuuming : Draw out air from conditioner . 
• Equipped with filter device to eliminate moisture and impurities .
• Drain compressor oil automatically .

Our Company :

WONDERFU was established in 1998. And we have 20 years’ experience in manufacturing automotive garage equipments. We are professional in producing refrigerant AC service machine.

Wonderfu will always offer you good quality products with competitive price.

Contact us now!