CNC Tools Carbide Milling Inserts CVD Coating 3PKT100308-MM Lathe Parts Tool

Carbide Inserts 3PKT Lathe Parts Tool Milling Inserts CNC Tools 3PKT100308-MM

Company Profile:

We are trading company have two factory in Sichuan .China.

A manufacturer with 8 years experiences of producing carbide cutting tools,

including carbide turning,milling,threading,grooving insert,carbide end mill,drill bits,etc.

Complete specification of carbide milling insert.

Currently we have more than 2000 different products from mainly brand all over the world.

sandvik,iscar,mitsubishi,kyocera,korloy,sumitomo,etc.

We can provide free samples for most products (except for a few special ones, we can communicate with you in detail).You can add me whatsapp to Communicate more.

My WeChat&whatsapp is: +86 18797881202

E-mail:874802564@qq.com

We produce imitation products, but we can provide you with products of various prices and quality. The cost performance will be very high. Ordering more than 500 pieces can be used for brand packaging.

1. Before installing the tool, first check the wear of the tool. If there are defects such as broken edge and serious wear, replace the tool with a new one or use it after repair.
2. Before installation, the relevant surfaces must be cleaned and wiped, and the burrs on the gasket and orifice must be carefully removed to prevent the dirt and burrs from affecting the accuracy of the tool installation position.
3. When clamping the tool with a washer, the two ends of the washer must be parallel to each other as far as possible. If the milling cutter is found to be skewed after installation, the washer position shall be adjusted to minimize the cumulative error of the washer. Until the milling cutter does not shake after driving.
4. When installing the taper shank milling cutter, the taper between the milling cutter, the intermediate sleeve and the spindle must be consistent, and the installation center and the tool center should be concentric as far as possible.
5. After the tool handle is inserted into the main shaft, the milling cutter is tensioned with the tensioning screw. It should be noted that the rotation direction of the milling cutter must be consistent with the thread direction of the pull rod, so that the thread of the pull rod and the milling cutter can be connected more tightly during the rotation, otherwise the milling cutter will be in danger of falling out.
6. Without affecting the processing, try to make the milling cutter close to the spindle bearing and the hanger bearing close to the milling cutter. If the milling cutter is far away from the main bearing, a hanger bearing should be installed between the main bearing and the milling cutter.
7. When installing the milling cutter, the key should not be removed. Because there is no key on the cutter shaft, if the force is uneven during milling or under the condition of heavy load cutting, the milling cutter tends to slip. At this time, the cutter shaft itself bears great radial resistance and resistance, which is easy to bend the cutter shaft and damage the fixed washer.
8. After the milling cutter is installed, check the relevant washers and nuts again to prevent loosening. Check the radial runout or end runout of the milling cutter with a dial indicator to see if it is within the allowable range.
9. After the cutter shaft is removed, it should be hung on the rack to prevent the cutter shaft from bending and deformation. In special cases, when horizontal storage is required, wood chips or other soft objects shall be padded to prevent scratches and deformation.

Q&A:
1. who are we?
We are based in Sichuan, China, start from 2019,sell to Eastern Europe(20.00%),Southeast Asia(20.00%),Mid East(20.00%),Southern Europe(20.00%),South Asia(20.00%). There are total about 5-10 people in our office.

2. how can we guarantee quality?
Always a pre-production sample before mass production;
Always final Inspection before shipment;

3.what can you buy from us?
Mechanical equipment and parts,Aluminium alloy products,building materials,metalware,alloy material

4. why should you buy from us not from other suppliers?
Mechanical equipment and partsAluminium alloy productsbuilding materialsmetalwarealloy materialHardware productsOnline trading agentImport and export of goods and technologies

5. what services can we provide?
Accepted Delivery Terms: FOB,FCA；
Accepted Payment Currency:USD,EUR,HKD,CNY;
Accepted Payment Type: T/T,PayPal,Western Union,Cash,Escrow;
Language Spoken:English,Chinese,Spanish,Japanese,Portuguese,German,Arabic,French,Russian,Korean,Hindi,Italian