Zhangjiagang RY Electronic CO.,LTD |
Verified Suppliers
|
Different Sizes Interna Dual band Built-in Active Ceramic 28dB UAV Aerial GPS Beidou Antenna
The working principle of ceramic antenna is that high frequency and low noise amplifier are used in the design of ceramic antenna unit to reduce the thermal noise of antenna and the influence of previous unit circuits on the performance of receiver. The function of ceramic antenna is to convert the electromagnetic wave energy of radio signal from satellite into the current that can be absorbed by electronic devices of receiver, so the size and shape of antenna are very small This is very important because it can determine the ability of ceramic antenna to obtain weak GPS signal.
Electrical Characteristics:
Ceramic antenna is another kind of miniaturized antenna suitable for Bluetooth devices. The types of ceramic antenna are divided into block ceramic antenna and multilayer ceramic antenna. Block antenna uses high temperature to sinter the whole ceramic body at one time, and then prints the metal part of the antenna on the surface of the ceramic block.
The multilayer antenna is fired in the way of low temperature co firing. The multilayer ceramic is laminated and aligned, and then sintered at high temperature. Therefore, the metal conductor of the antenna can be printed on each layer of ceramic dielectric layer according to the design requirements. In this way, the antenna size can be effectively reduced, and the purpose of hiding the antenna can be achieved. Because the dielectric constant of ceramic is higher than that of PCB, ceramic antenna can reduce the size of antenna effectively
Ceramic antenna is made of ceramic and weighs only 200g. Its frequency range is between 902mhz and 928mhz. Moreover, the dielectric loss of ceramic is smaller than that of PCB, so it is very suitable for Bluetooth module with low power consumption. The effect of ceramic antenna is better than that of on-board antenna. Generally, it has ant access pin and anchor, so it is very convenient to use.
The ceramics of ceramic antenna are used in radio. In addition to capacitors, there is also a device called ceramic filter (because it is connected to the antenna circuit, many people mistakenly think it is an antenna). It is made of lead zirconate titanate ceramic material. The ceramic material is made into flakes, and both sides are coated with silver as electrodes. After DC high voltage polarization, it has piezoelectric effect. It plays the role of filtering and has the characteristics of stability and good anti-interference performance.
Ceramic antenna has four important parameters: gain, VSWR, noise figure and axial ratio. Especially the axis ratio, which is an important index to measure the difference of signal gain in different directions.
The working principle of ceramic antenna is to use GPS satellite to achieve navigation and positioning, and the main task of the user's receiver is to extract the pseudo-random noise code and data code in the satellite signal to further calculate the position, speed and time (PVT) and other navigation information of the receiver carrier. The principle of ceramic antenna is divided into two parts: one is the transmitting antenna, the other is the receiving antenna.
Working principle of ceramic antenna
Ceramic antenna transmitting antenna is to transform the high-frequency electric field formed between the antenna and the ground into electromagnetic wave through an electrode called "antenna", so that it can be transmitted to the distance.
The receiving antenna of ceramic antenna simply means that the electromagnetic wave from the air is induced into electric field by an electrode called "antenna", which generates high-frequency signal voltage and sends it to the receiver for signal processing.
Product Details
Our Company
1. RY Electronics has over 10 years of experience designing and
manufacturing custom cable assemblies and antennas in large or
small volumes depending on your needs.
2. Our manufacturing facilities can build just about many types of
custom cable assembly(LVDS cable/Flat cable/RF cable/wire harness)
as well as GPS/WIFI/ISM/GSM/3G/4G antenna and RF connectors.
Why us ?
1. Factory sell directly
2. 1 years quality warranty
3. Samples will be shipped in 2-4 working days
4. Exchange goods without reasons within 7 days
5. Support alibaba assurance order with your money safety and your order safety
6. OEM&ODM
FAQ
1. When can I ?
We usually quote within 24 hours after we get your inquiry. If you
are very urgent to get the price, please call us or tell us in your
email so that we will regard your inquiry priority.
2. How can I get a sample to check your quality?
After price confirmation, you can require for samples to check our
quality.
3. How long can I expect to get the sample?
After you pay for the sample charge and we confirm the drawing with
each other, the samples will be ready for 3-5 days. The samples
will be sent to you via express and arrive in 3-5 days. You can use
your own express account or prepay us if you do not have an
account.
4. Can you do the design for us?
Yes. We have a professional engineer having rich experience in wire
harness & cable assembly design. Just let us know your ideas
and we will help to carry out your ideas into perfect products. It
does not matter if you do not have someone to complete files. Tell
us your detalied SPEC. of products, and we will send you finished
drawing for confirmation.
5. What about the lead time for mass production?
Honestly, it depends on the order quantity and the season you place
the order. The lead time of MOQ is about 10 to15 days. Generally
speaking, all of the goods can be reach your address within 4
weeks.
6. What is your terms of delivery?
We are accept EXW, FOB, CIF, etc. You can choose the one which is
the most convenient or most cost-effective for you.