24V Electric Vehicles Automotive Electric Water Pump For Car Engine

BSP-P300-CAN SERIES brushless DC water pump

Boosting/circulation/Variable-frequency/Low-noise/shield pump/CAN control/

Changzhou Bextreme Shell Motor Technology Co.,Ltd

Electric water pumps have electric motors that are powered by the vehicle’s electric system. Their function is also controlled electronically by the ECU, which means the ECU will tell the water pump when to turn on and off. Electric pumps also do not have shaft seals or bearings, and are not belt driven, so they experience very low stress levels compared to mechanical pumps.

Longevity
Since electric water pumps experience much less stress, undergo fewer hours of operation, and are sealed differently compared to mechanical water pumps, they’re more likely to last. As a result, water pump replacements will become less common as EVs become more popular.

Versatility
Mechanical water pumps cannot be used in electric vehicles, but electric water pumps can be used in some newer internal combustion engines. In internal combustion vehicles, they may be used for coolant circulation through the turbocharger, supercharger, heater core, and sometimes as the main engine coolant pump.
 
■ Technical description (related parts in contact with the liquid)
Pump head housing: PPS+GF
Impeller: PPS+GF
Shield cavity: PPS+GF
Shaft sleeve: Carbon resin composite materials
Shaft: stainless steel shaft
Magnet housing: nylon plastic capsulation
Seal ring: EPDM
 
■ Driving device (Including motor)
Driving electromagnet: nylon plastic capsulated magnet
Screws and nuts: SUS 304 stainless steel
Driving Motor: brushless motor
Motor wireframe: PPA GF
Pump housing: Die-casting aluminum case with sandblasting and impregnation treatment
 
Bracket: Carbon steel
Bracket hoop: SUS 304 stainless steel
Waterproof based on IP68 rating (en60529)
Connector model: AMP282106-1 (matched PlugAMP282088-1)
Nozzle diameter:40mm/25mm
■ Model Specifications
BSP-P300-CAN-25(25mm nozzle)
BSP-P300-CAN-40(40mm nozzle)
 
 
■ Mounting instruction
BSP-P300-CAN series pumps are centrifugal pumps that require pre-filled,
The pump is installed in the lowest position of the system to ensure that the impeller is always immersed in the liquid, or pre-filled the pump before power on.

1: The pump should not be dry-running, even though it can dry-running for 15 minutes (after 15 minutes of dry-running, it will automatically stop the motor), Dry running will make noise, also increasing abrasion to the shaft and shaft sleeve.
 
2:Use the recommended diameter pipe connecting the pump inlet, if you use a smaller diameter hose pump inlet, Due to the negative pressure in the pump, the outside air easier entrance to the pump through the pipeline, it will make the pump performance degradation, and also the air bubbles make damage to the pump.
 
3: As viewed from the pump inlet direction, the impeller rotates clockwise (see the arrow on the outlet port).
 
4: The pump can be installed vertically or horizontally mounted (see figure 1 ) When installed vertically, the outlet port should be upward.
 
5:In order to avoid the dry-running (air getting stuck in the impeller), the water pump outlet port should be vertical or in the upper of the impeller. (see figure 1 )
 
6: The connected pipe should be vertically mounted (or no elbow in 20cm )to make the air discharged easily, the outlet pipe should not be used less than 90 degrees
Elbow (see figure 2).
 
7: Can't use seawater or other heavy pollution with big grain impurity liquid as the liquid medium.
 
 
■ Temperature parameter
Medium liquid temperature: -40℃ to +100℃ (-40°F to + 212°F)
Working ambient temperature: -40℃ to +120℃ (-40°F to +248°F)
Storage temperature: -40℃ to +70℃ (-40°F to +158°F) (up to 100 ℃, but it will shorten the service life)
■ System pressure
-0.2 to 2.5 bar ( 100℃ (212°F).
The service life is more than 20,000 hours based on the rated voltage and 36℃(86°F) ambient temperature.
■ Voltage range
Rated 24V water pump, workable range 18V - 32V
Although the motor can be used in a wide range of voltage and temperature, excessive or too low voltage and temperature will affect the service life of the motor, and the pump can not be exposed to thermal radiation ambient.
 
Medium liquid: pure water, liquid mixture (Water with below 60% glycol)

 
 
 
 
 
 
 
 
■ Electrical parameter
 
 
Connector model and the corresponding electrical properties (see figure 3):

 
 
 
 
 
 
■ Attentions
1. Working ambient temperature:-40℃--120℃, should try to avoid close to three-element catalytic, gas discharge pipe system, and engine during the installation, and ensure the working environment temperature.
2. The installation position of the water pump should as much as possible close to the low water level, to extend the service life of the pump.
4. Please use the pump far from the dusty environment, the dust is harmful to reduces the service life
5. Pay attention to the purity of the water, avoid to jam and impeller-blocked to reduce the service life of the pump
 
 
 
■ Performance parameter

 
 
 

• External dimension(25mm nozzle)

• External dimension(40mm nozzle)