Active Member
|
[China]
Address: T2-715, Landmark Plaza, High-Tech Zone, Chengdu, China
Contact name:Mike Ma
Chengdu Ample Import And Export Co., Ltd. |
|
|
Fume hoods are designed specifically to provide ventilation for the protection of lab occupants during chemical manipulations. The airflow they provide is greatly in excess of that needed for storage of closed containers of even the most toxic of volatile materials. Storing materials in this way is, therefore, a misuse of an expensive piece of equipment.
In general, the storage of chemicals in fume hoods is strongly
discouraged. The realities of available space and equipment in
some laboratories may make it difficult or impossible to completely
prohibit the use of hood workspaces for storage.
Changes or additions to an existing fume hood without the explicit
approval of the department's facilities manager or Special
Facilities supervisor is prohibited. Adding devices to even the
simplest exhaust system without adequate evaluation and adjustment
will usually result in decreased performance of the existing hood
and/or inadequate performance of the additional device.
Additionally, some components of older hoods may contain asbestos
and therefore should not be damaged.
| Model Specification | WJ-1500A | WJ-1500B | WJ-1800A | WJ-1800B |
| External dimensions of equipment(mm) | 1500(W)*1205 (D) *2400 (H) | 1800(W)*1205 (D) *2400 (H) | ||
| Dimension of works pace (mm) | 1260(W1)*780(D1) *1100 (H1) | 1560(W1)*780(D1) *1100 (H1) | ||
| Panel material | 20+6mm thick butterfly ceramics | |||
| Material of internal lining board | 5mm thick ceramic fiber board | |||
| Diversion structure | Lower air return | |||
| Control system | Button control panel (LCD panel) | |||
| PH value control | The medium is alkaline water solution; manual monitoring, and manual control through acid pump and alkali pump. | |||
| Input power | Three-phase five-wire 380V/50A | |||
| Current for air fan | Not over 2.8A(380V or 220V can be directly connected) | |||
| Maximum load of socket | 12 KW(total of 4 sockets) | |||
| Water tap | 1 set (remote control valve + water nozzle) | No | 1 set (remote control valve + water nozzle) | No |
| Water discharge way | Magnetic chemical pump strong discharge | |||
| Using environment | For non-explosion indoor use, within 0-40 degrees Celsius. | |||
| Applicable fields | Inorganic chemistry experiment; Food, medicine, electronics, environment, metallurgy, mining, etc. | |||
| Ways of Purification | Spray sodium hydroxide solution, no less than 8 cubic meters/hour | Spray sodium hydroxide solution.no less than 12 cubic meters/ hour | ||
| Ways of surface air speed control | Manual control (through the electric air valve to adjust the exhaust air volume or adjust the height of the moving door) | |||
| Average surface air speed | 0.6-0.8 m/s Exhaust air volume: 1420-1890m3/h (when door height h =500mm) | 0.6-0.8 m/s Exhaust air volume: 1760-2340m3/h (when door height h =500mm) | ||
| Speed deviation of surface air | Not higher than 10% | |||
| The average intensity of illumination | Not less than 700 Lux; Standard white and uv-free yellow LED lamps; The illumination is adjustable. | |||
| Noise | Within 55 decibels | |||
| Flow display | White smoke can pass through the exhaust outlet, no overflow. | |||
| Safety inspection | No spikes, edges; Charged body and the exposed metal resistance is greater than 2 mQ; Under 1500V voltage, no breakdown or flashover occurred for 1min test. | |||
| Resistance of exhaust cabinet | Less than 160 pa | |||
| Power consumption | Less than 1.0kw/h (excluding power consumption of fans and external instruments) | Less than 1.2kw/h (excluding power consumption of fans and external instruments) | ||
| Water consumption | Less than 3.2L/ h | Less than 4.0L/ h | ||
| Performance of wind compensation | With a unique wind compensation structure, the volume of the wind will not cause turbulence in exhaust cabinet and will not directly blow to the staff (need to connect to the air compensation system of the laboratory) | |||
| Air volume regulating valve | 315mm diameter flanged type anti-corrosion electric air flow regulating valve (electric contact actuator) | |||
1.
All operations that may generate hazardous air contaminants must be done inside a laboratory fume hood.
2.
Fume hoods do not prevent accidents or chemical splashes.
3. Hood users must be trained in the proper operation and use of laboratory fume hoods.
4.
The hood should not be operated unless it is verified that it is working correctly.
5. Safety glasses (goggles), lab coats,
and appropriate chemical gloves must be worn when
working in, on, or around the fume hood.
6. Do not put your head in the hood,
beyond the sash opening.
7. Do not use the hood for storage of equipment,
containers, or chemicals which are not going to
be used during the day.
8.
Equipment and materials placed in the hood must not block hood slots,
airfoils, or otherwise interfere with
the smooth flow of air into the hood.
9. Never place or use equipment that protrudes beyond the face of the hood (sash opening).
This configuration
will disrupt air flow of air into the
hood and reduce its efficiency.
10.
Keep all equipment and materials at least 6
inches behind the plane of the sash (hood
face), this will improve containment capture.
A stripe (tape) on the hood working surface is a good
reminder.
11.
Place all bulky equipment away from the sidewalls to allow air flow around the equipment.
When the exhaust is running, it sucks in volumes of air through the
open side (never run the exhaust with the hood completely closed)
and vents it through the duct. The duct may throw the fumes right
outside the room in the air, or may run it through a filtration
system, depending upon the severity of the experiment.
Inside the fume hood, there are facilities to let you work. For
example, there is almost always some good lighting system in the
cabinet. There should be LPG and water connections in the hood, and
a drain too in case of spills.
The air suction system is generally placed on top of the box or on
the backside (the side towards the wall). This system is generally
made up of a strong exhaust fan or air pump and accompanying air
duct. The strength of the pump lies in the airflow strength
starting from 4 to 8 meters per second to more.
Some advanced laboratory fume hoods have microcontrollers inside
them, which you can use to control the exhaust. You may set various
suction levels for given setups and later use these quick setups
for particular experiments. You can also control the fan/pump power
during the experiment too, and the lights as well.
