T5 Lightweight Aluminum Square Tubing Powder Coating Recessed Linear Flanged

T5 Lightweight Aluminum Square Tubing Powder Coating Recessed Linear Flanged

Alloy Aluminum Industry Extrusion Profile 6063-T5 Powder Coating Recessed Linear Flanged

Profile Detail:

Aluminum Profile Produce Process:

Process specification for oxidizing production of aluminium material

Oxidation process

1: The process parameters: the concentration of H2SO4 160-175 g/l, AL3+ < 20 g/l, current density 1-1.5A/dm, voltage 12-16V, oxidation tank temperature 18-22, according to the formulas to calculate the power on time. The film material 3-4 m provisions: silver white sand, 4-5 m, 7-9 m electrophoresis;

2: The anode frame shall be stably placed in the conductive seat and check and confirm that the contact between the profile and the cathode plate can be electrically oxidized;

3: Oxidation end, the anode rod hanging from the surface tilt, and drop the residual liquid, into the clean water tank cleaning for 2 minutes;

4: The non colored section can enter the two stage water tank to be treated with sealing hole.

Coloring process

1: Process parameters: SnSO4 5-6g/l; NiSO4 16-18 g/l; 9-12 g/l 17-20 stain free acid; g/l; pH =0.8-1.2, bath temperature of 19-21 DEG C, coloring voltage should be lower than the oxidation voltage 14-16V; usually add the following ratio: SnSO4:NiSO4=1:1; color additives: SnSO4=1:1

2: Coloring products only with a single row of double row rolling way, the corresponding width of the spacing between two adjacent products or products, generally with the finger test more than two finger width, tie line must be tight, solid bar can only use the new tie line;

3: When the coloring products are oxidized, the oxidation bath temperature must be controlled at 18-22 DEG C to ensure uniform film thickness and fine structure;

4: The coloring area of each row of the coloring products should be basically the same;

5: After coloring, the carrier is inclined and is cleaned with a color guide. After the conditions are met, the water will be washed again. Otherwise, the following conditions will be dealt with;

6: The color is shallow, back into the coloring trough, according to the complementary switch coloring time shall not exceed 2 minutes; deep color, should be put into the corresponding oxidation tank tank fade, or fade to the ideal air suspension so far; oxidation products must be approved by three or more washing before entering the coloring trough a final water washing tank, which was PH 5;

7: The coloring products prohibited in the sink after long-term immersion in oxidation, general soaking time should not exceed 3 minutes;

8: The product enters the coloring trough, should be without electricity, soak for 1 minutes or so, and then began to electrify coloring, coloring process began, about 30s in stably coloring voltage up to 14-18V, and then keep the voltage stable until finished coloring;

9: To avoid as much as possible in different batches of different varieties of products, products are colored in the same frame;

10: The coloring after two times washing before postprocessing, control PH value of the first water washing, PH = 2, PH = 5 second.

Corporate Introduction:

Foshan Dolphin Metal Products Co., LTD is located in Foshan Guangdong. We have been engaged in foreign trade for more than 10 years. The company has two factories in China and one in Vietnam. We provide various high-standing T5&T6 6000 series aluminum profile for doors&windows, conservatory, cabinet&wardrobe, building material and etc. With professional R&D, OEM/ODM are available. Our monthly output reaches more than 8000 Tons, so our customers come from different countries, such as Thailand, Malaysia, Singapore, Vietnam, Burma and etc.

Moreover, the company has a professional and responsible team to help our customers. All processes are visualized during thr order. Before loading, we have quality inspectors to check the products. After the order, the aftersales staff will ask for feedback. We have always been adhering to the concept that customers are friends and teachers. Every feedback is a opportunity to learn and grow. With the development of these years, Dolphin Co., LTD will be further upgraded and expanded.

Please tell us the information below, and we will give the best suggestion to you !

1. Where you intend to use the aluminium profiles?

2. If you have the estrusion drawing, send us and we develop the correspondence mold.

3. Which color you want or tell us the architectural style you like.

4. Purchase quantity. It will convenient us to give you the best price.