Wall Mounted Gas Alarm Control Panel IP30 YA-K210 With LED Display

Wall Mounted Gas Alarm Control Panel Gas Detector Controller With LED Display Gas Detector Controller

Product Description:

The YA-K210 gas alarm controller is a highly advanced gas detection and early warning system that is specifically designed for industrial environments. To form an industrial gas intelligent control system, this controller can be combined with our YA-D series gas detectors.

With a 7 inch industrial LCD screen, the controller can display the concentration value of all gas detectors. The detector can be connected to the controller with a branch line (4-20mA) or bus (485 bus), and up to 256 detectors can be connected.

The controller boasts a range of functions including low limit, high limit, fault, and shielding alarm functions. Upon an alarm, the system sends the corresponding alarm sound and light signals, indicating the alarm location and recording the alarm time. Each gas detector can also be configured with two sets of output relays for low alarm and high alarm, which can drive the exhaust fan, solenoid valve, and other equipment. Alarm records can be exported through the U disk. Additionally, the product has two groups of PC interface to allow for easy querying and data analysis on a host computer.

The product is designed according to national standards and has a fast response time, low failure rate, and easy maintenance. It is wall-mounted for convenient installation and data processing and display is performed via the controller CPU.

Features:

YA-K210 Gas Alarm Controller Host

The YA-K210 gas alarm controller host is embedded with a microprocessor that performs a multitude of functions including detector signal sampling, data real-time calculation, system fault detection, power management, key scanning, display driver, alarm display, fault display, shield display, data storage, data export, 4G networking, alarm peripheral driver, and more.

The device features an intelligent system that allows switching between μmol/mol and mg/m³ units, and comes equipped with 2 groups of common relays and 6 groups of programmable relays for passive output with the option to connect to an external relay linkage module if required.

It supports multiple mainstream communication methods such as 4-20mA, RS485, LoRa, 4G, and PC. The YA-K210 gas alarm controller host allows for real-time monitoring of the measured gas concentration in the detection area, and sends corresponding acoustic and optical alarm signals when the gas concentration reaches or exceeds the set alarm value.

Additionally, the connected external device can act on its own when the preset logic relationship is satisfied. External devices can also be started directly through the controller. The device records separation, fault, alarm, and automatically screens and separates system records. It can store up to 2000 records, which can be connected to a U disk for data export.

The power supply utilizes 220V 50Hz AC, and the backup power uses two 12V/9Ah batteries.

Technical Parameters:

The Gas Alarm Controller is a component of the Gas Leakage Prevention System. It supports a maximum of eight 4-20 MA inputs and 99 RS485 data inputs, and it is recommended to use only the local power supply to connect no more than 12 sets at the same time. The output signal is RS485 and 4-20mA. It has a warranty of 1 year.

Applications:

The YA-K210 Gas Alarm Controller is suitable for a wide range of application occasions and scenarios. It is an ideal product for use in industrial plants, commercial buildings, and residential areas where there is a risk of hazardous gas leaks. This gas alarm controller can be used to detect and monitor gas leaks such as methane, propane, carbon monoxide, and other hazardous gases. It can also be used as a natural gas alert system to detect natural gas leaks in homes and other areas.

The YA-K210 Gas Alarm Controller can support a maximum of eight 4-20 MA inputs and 99 RS485 data inputs. However, it is recommended to use only the local power supply to connect no more than 12 sets at the same time to ensure the safety and reliability of the system. This gas alarm controller can output signals via RS485 and 4-20mA, and it has an output supply voltage of DC24V±25%.

The RS485 gas alarm controller is an essential component in any hazardous gas control system. It allows for remote monitoring and control of the gas detection system, enabling quick response to gas leaks and preventing potential hazards. The YA-K210 Gas Alarm Controller is a reliable and efficient option for any gas detection and control system. It is suitable for use in various application scenarios, including industrial plants, commercial buildings, and residential areas.

In summary, the YAOAN Gas Alarm Controller YA-K210 is a high-quality hazardous gas controller that is designed to provide a reliable and efficient solution for gas detection and control. It is suitable for use in various application occasions and scenarios, including industrial plants, commercial buildings, and residential areas. With its compatibility with the YA-D Detector Series, lightweight design, and output signals via RS485 and 4-20mA, this gas alarm controller is an excellent option for any gas detection and control system.

FAQ:

Q: What is the brand name of the gas alarm controller?

A: The brand name of the gas alarm controller is YAOAN.

Q: What is the model number of the gas alarm controller?

A: The model number of the gas alarm controller is YA-K210.

Q: Where is the gas alarm controller made?

A: The gas alarm controller is made in Shandong, China.

Q: What type of gas can the alarm controller detect?

A: The alarm controller can detect various gases, such as natural gas, methane, propane, and carbon monoxide.

Q: Can the gas alarm controller be connected to a smart home system?

A: Yes, the gas alarm controller can be connected to a smart home system for remote monitoring and control.