12V Modular Renewable Energy Lab Equipment Vocational Solar Energy Trainer

ZM2101 Solar Energy Modular Trainer Vocational Training Equipment Renewable Training Equipment

The trainer must correspond to a system for the study of the electrical installations with off grid photovoltaic solar energy.

It must be composed of a photovoltaic inclinable module, 90 W, 12 V, complete with a cell for measuring the solar irradiation and with a temperature sensor and a supporting frame for the following modules:

•battery protection module, 12 V, 32 A with the following components:

-32 A circuit breaker for control of the battery,

-LED indicator for the battery connection,

-4 mm security terminals black/red.

•a rheostat module including knob for varying the resistance and terminals. Range: 0-80 Ω.

•measuring instrument module to perform measurements of a photovoltaic system. It must include a series of instruments; input terminals +/- are placed on the left of each instrument and the output terminals must be on the right. It must provide DC, AC and environmental measurements. All instruments must show readings using the automatic decimal point position, starting from 1/1000 up to the maximum value of each measurement. Communication terminals must be located on the right low side of the panel; two RS485 connectors, one male and one female, must be available for the connection with the PC running the acquisition software and/or with other modules in a chain configuration. Instruments must support MODBUS RTU protocol over RS485 interface, used by the software application, available separately, to perform a guided analysis of the electrical characteristics on the modules of the trainer. The module must include 4 multifunction displays:

-No.2 for DC measurements and displaying data for Voltage, Power and Current: DC voltage ± 65V, DC current ± 30A, DC power autoscale,

-No. 1 display for AC measurement: AC voltage 0-512V, AC current ±30A, Power Meter,

-No. 1 display showing data for: Solar irradiance meter 0 ÷ 1000 W/m2, Thermometer 0 ÷ 400°C.

Connections of the Measuring Instrument Module:

-Connector for the calibrated cell and for the temperature sensor.

-Power supply connectors of the module: DC voltage must be between 10V and 35V.

-Power switch, for the module switching on/off.

-Connectors for DC signals measuring voltage, current and power.

-Connectors for AC signals measuring.

-RS 485 Communication port, for the SW application interface.

•charge regulation module for charge regulation of the battery with the current supplied by the solar panel, it must include LCD screen to provide information on situations; the module must have protection against overload, temperature compensation, different charge modes of the battery (slow, fast, maintenance mode, etc), DC solar panel terminals, DC battery terminals & DC load terminals. Characteristics:

-Maximum charge current 30 A,

-Short-circuit current 30 A,

-Input voltage 12 V,

-Protection IP22.

•load module with two 12V lamps, dichroic and LED; each lamp must incorporate an on/off control independent switch and 2 DC terminals.

•load module with two AC loads (230 V, 50 Hz). The upper one shall be a halogen lamp, and the lower one a LED lamp and 2 AC terminals.. They can be switched on/off independently.

•DC to AC inverter module, it must include control circuits against the output overload and against the deep discharge of the battery, rated power: 300 W, input voltage: 10.5-16V. The module must have DC terminals, on/off indicator, battery low or output overload indicator and mains terminals. It also must include the following connectors and indicators:

-DC 12 V – DC feed at the indicated voltage,

-ON – Status: on when the inverter is active,

-Low Battery & Overload – Status: battery low or output overload,

-MAINS – Output of the mains (230 Vac).

•Battery module.

With this didactic system it shall be possible to perform the following experiments:

Basics of the Solar Trainer:

•Identification of the components of the trainer

•Measuring the load current, voltage and power

Irradiation and Temperature Measurements:

•Setting the solar panel to the most irradiated position

•Changing the inclination of the solar panel

•Changing the azimuth of the solar panel

•Covering the solar panel with different materials

Solar Irradiation throughout the Day:

•Obtaining the solar irradiation data

Solar Panel Voltage-Irradiation Curve, Current-Irradiation Curve and Resistance of the Solar Panel:

•Obtaining the solar panel voltage-irradiation curve

•Calculating the inner resistance of the solar panel

Current-Voltage Characteristics of the Solar Panel:

•Obtaining the solar panel current-voltage curve

Solar Panel Power Measurements:

•Obtaining the solar panel current-power curve

•Overloaded solar panel measurements

Using Solar Panel to Charge the Battery:

•Battery charging

Using Solar Panel and Battery to Power DC Load:

•Supplying DC load

Using Solar Panel and Battery to Power AC Load:

•Supplying AC load.

The modules must be insulated type and it must be possible to mount them on a two level vertical frame supplied with the system.

The trainer must include a processing software designed in labview.

The trainer must be supplied with a set of interconnecting wires and manual in English language.

Product Details and Warranty

We supply suitable spare pats according to experiment requirement, our products take aluminum structure, A4 paper dimension aluminum and plastic hanging box structure.

We supply 3 years warranty time.

Packaging & Delivery

Package details: plastic film+ plastic foam + plywood box with pallet, and for equipment dimension less than 1CBM, we supply plastic film+ plastic foam+ fine carton.

Arrange delivery within 45 days upon receipt of payment.

Please see below photo for detailed package.

Arrange delivery within 45 days upon receipt of payment.

Please see below photo for detailed package.

Training Room Photo

Company Information

We supply professional educational training equipment and technical teaching equipment, which has been widely applied in Engineering Universities, Polytechnics, Technical Institute, Vocational Schools as well as Industry workforce Development Programs and Training Center. Our products allow students to learn and experiment through valuable hands-on experience, and the technology covered by our training equipment provides knowledge, experiments and didactic skills development that are of critical importance to today´s and tomorrow´s careers.

Photo for Clients Visiting Factory

Service

We supply supply7*24 hours service, customer design service, OEM service, buyer label service. With professional engineers team and sales team, we assure you good product quality.

Certificate

Our products takes ISO9001 product management system.