Educational Equipment Trainer Experimental Simulator of Air Conditioning, Temperature and Constant Humidification

ZM6224 Educational Equipment Trainer Experimental Simulator of Air Conditioning, Temperature and Constant Humidification

• You must provide an experience for a 4-force ventilation system and a heat pump air conditioning system.

  It consists of an auxiliary heating device with heat pump and humidification, usable with hot and cold water.

  The humidification device must have a sprinkler system that allows air to cross. You can evaluate and compare its performance and you can adjust the intake / exhaust valve.

  The temperature of hot and cold water can be adjusted by the user.

  The complete equipment should be designed to check the operation from the outside, and the temperature inside is adjustable.

  The complete equipment must have an automatic control system, due to the temperature and organic humidity.

  The sequence panel should consist of the automatic control of the graphic device, and should give an experience and train in the control of temperature, pressure and humidity adjustment, connecting the circuits to the power supply.

  You should be able to protect the overload and operate the pressure switch, alarm bell and an indicator light, while problems with the thermostat occur.

  You must control the power (ON / OFF), the monitor, and the data stored in the computer of the electrical control panel through item 1. It must have insertion and simulation of faults, User manual in Spanish with theory and practices for instructor and student

  Size: 1800x1000x1000mm

  Freezer main controller

  - Adopted 32-bit high-performance ARM processor

  - Built-in USB port for PC connection

  - Up to 16 temperature modules can be interlocked

  - Built-in RS-485 communication terminal for multipoint communication

  - The RS-485 communication circuit must be designed as an insulation structure to improve noise immunity.

  - 12-bit AD input for pressure and humidity sensor interlocked 16Ch

   

  - Built-in 16-channel digital input for function control.

  - 16 built-in LEDs to verify the output status inside the PCB

  - Built-in 16 external LEDs to verify the output status

  - Up to 16 relay output channels (8 basic channels, 8 optional channels)

  - The relay for the output must have a rating of 10 A or higher.

  - The SMPS and DCDC converter must be integrated and designed with an external signal and an insulation structure.

  - Power source: AC86 ~ 264V, 50 / 60Hz free voltage

  - Within the size of PCB 250X140

  It should contain the components listed below as:

  Compressor: 1 / 2HP, single phase 220V, control box.

  Condenser: Air cooled.

  Heat exchanger for hot and cold water, clamp type. (2 pieces)

  Evaporator for heat pump: pin, air-cooled tube (Soldier)

  Liquid Receiver: 1 / 2HP

  Accumulator: 1 / 2HP

  Expansion valve (2 pieces): Manual.

  Electronic valve (4 pieces): 3/8 ’’ clamp or welded type.

  Filter dryer: 3/8 ’’ clamp or welded type.

  Pressure gauge: High pressure, Low pressure.

  Loading nozzles

  Acrylic visor: clamp or welded.

  Transport pump (3 pieces): 220V, 60Hz

  Seal valve 220V, 60Hz

  Exhaust valve: 220V, 60Hz

  Humidification device: Spray and atmospheric crossing type.

  High and low pressure switch: LPS, HPS, VOLT, AMPERIMETER

  Temperature sensor 13 pieces

  Refrigerator temperature module

  - Built-in 4Digit FND with good visibility

  - Up to 16 temperature modules can be interlocked

  - Built-in RS-485 communication terminal for multipoint communication

  - RTD type temperature sensor input

  - Accuracy within ± 0.2 degrees

  - Built-in 10A rating relay

  - Built-in 4-bit rotary switch for address configuration

  - Using a 10 A output relay

  - Power source: DC24V

  - Front PCB size within 70X50

  Pressure sensor 2 pieces

  Humidity sensor 1 pieces

Product Details and Warranty

We supply suitable spare pats according to experiment requirement, our products take aluminum structure, A4 paper dimension aluminum and plastic hanging box structure.

We supply 3 years warranty time.

Packaging & Delivery

Package details: plastic film+ plastic foam + plywood box with pallet, and for equipment dimension less than 1CBM, we supply plastic film+ plastic foam+ fine carton.

Arrange delivery within 45 days upon receipt of payment.

Please see below photo for detailed package.

Training Room Photo

Company Information

We supply professional educational training equipment and technical teaching equipment, which has been widely applied in Engineering Universities, Polytechnics, Technical Institute, Vocational Schools as well as Industry workforce Development Programs and Training Center. Our products allow students to learn and experiment through valuable hands-on experience, and the technology covered by our training equipment provides knowledge, experiments and didactic skills development that are of critical importance to today´s and tomorrow´s careers.

Photo for Clients Visiting Factory

Service

We supply supply7*24 hours service, customer design service, OEM service, buyer label service. With professional engineers team and sales team, we assure you good product quality.

Certificate
Our products takes ISO9001 product management system.