Home Companies Chengdu Bebort Electric Equipment Co., Ltd.

Variable Speed Drive Digital Power Inverter 400VAC High Disturbance Resistance

Contact Us

[China]

Trade Verify

Address: 7-5-706#, Dajian Road 280#, Shuangliu District Chengdu City, SC China 610225

Contact name:Valerian Lau

Chengdu Bebort Electric Equipment Co., Ltd.

Verified Suppliers
  • Trust
    Seal
  • Verified
    Supplier
  • Credit
    Check
  • Capability
    Assessment

Variable Speed Drive Digital Power Inverter 400VAC High Disturbance Resistance

Country/Region china
City & Province chengdu sichuan
Categories Switches

Product Details

0.75kw-15KW sensorless vector control frequency inverter/ac drives/variable speed drive (built-in brake unit)

 

CDE360 Technical Specifications

 

ItemSpecifications
Basic PerformanceRated Input

Single-phase: 220V;

Three-phase : 220V/380V/480V;

Frequency: 50/60Hz

Input voltage range

Voltage fluctuation: -15%~10%;

Imbalance factor: less than 3%;

Voltage frequency: 47~63Hz

Control modeVF control; Open-loop vector control; Close-loop vector control
Frequency resolution

Digital setting: 0.01Hz;

Analog setting: 0.5% × maximum frequency

Maximum outputV/F control: 3500Hz; Vector control: 300Hz
Speed rangeVF control: 1:60; Vector control: 1:100
Carrier frequency0.5~16.0kHz(Model dependent). The carrier frequency can be automatically adjusted based on features of the load.
Start torque0.5Hz/150%*rated motor torque
Overload capacity

G type: 150% rated current for 60s,180% rated current for 3s

L type: 120% rated current for 60s

Basic FunctionRun modeKeypad; Control terminals (two-line, three-line); Serial communication (RS485).The user can perform switch-over between these sources in various ways.
V/F curveStraight line type; Multiple point type; N-power type
Ramp curveStraight line or S curve; Four ramp times (range: 0.1s to 6000.0s)
Torque boostAutomatic/manual torque boost
Speed traceAll types have the function of the speed trace.
Motor brakingDC braking; Energy consumption braking; Magnetic braking
DC braking

Braking frequency: 0.00Hz to Maximum frequency;

Braking time: 0.0s to 100.0s;

Braking current: 0.0% to 100.0%*Rated motor current

Magnetic braking

For occasions which have the request of fast stop or regenerative

loads, the function of magnetic braking can be used. The function

can avoid frequent protection due to over voltage.

CBC current limiting

The function of CBC current limiting is to minimize the fault of over

current and keep the normal running of the AC drive.

Overcurrent and overvoltage control

The function is to restrict the current and voltage automatically

during running and avoid the frequent fault protection of over

current and over voltage.

 

 

ItemSpecifications
Special FunctionsThe delay time of terminalsThe user can set the delay time for digital input terminals, digital output terminals and relays.The time range is 0.0s to 3000.0s.
JOG Control

Control mode: keypad, terminals and serial communication.

Frequency: 0.00Hz to Maximum frequency;

Ramp time: 0.1 to 6000.0s

Multiple speed and simple PLC

Based on built-in PLC or digital input terminals, realize the

running of sixteen segments speed.

Two PID inside the parametersAs common PID, the closed-loop system of process control can be realized easily.
Fixed length and count

The AC drive can count the pulse signal of 0 to 100K Hz and realize

the control of count reaching by using digital output terminals.The drive can also convert the count into length for display and control.

Spinning and swing frequencyThe fixed swing magnitude, fixed mutations and fixed periodic output can be achieved at arbitrary frequency.
Timing control

Time range: 0 to 65000 hours.

The timing control can stop the AC drive.

Power loss ride throughWhen the power loss ride through happens, by decreasing the running frequency, the feedback energy of the load can compensate the voltage drop of the DC bus. As a result, the AC drive can keep running for a short time.
Peripheral terminalsReference power

10V/30mA.

Usually, it is used for the power supply of analog input signals.

Control power24V/200mA.Usually, it is used for the power supply of digital input and output terminals.
Analog input

Two analog input terminals, which have two types of voltage input and current input.

Every input terminal can support three types input signals: 0 to 10V, 0 to 20mA and -10V to 10V.

These two analog input terminals are programmable.

Analog output

Two analog output terminals, which have two types of voltage output and current output.

Every output terminal can support two types output signals: 0 to 10V and 0 to 20mA.

These two analog output terminals are programmable.

Digital inputFive multi function digital input terminals are compatible with active PNP or NPN input mode. Among these six input terminals, the X6 terminal can be chosen as high-speed pulse input terminal and the range of the high-speed pulse is 0 to 100KHz. At the same time, the X6 terminal is programmable.
Digital outputThere are two open collect output terminals. Among them, Y2 terminal can be chosen as high-speed pulse output. These two output terminals are programmable.There are two relay output terminals.
ItemSpecifications
Protection functionCommon typesInput and output phase loss protection,under voltage protection, over voltage protection,over current protection,over heat protection, over load protection,short-circuit protection, module fault, external fault, self-defining fault.
EnvironmentInstallation locationIndoor, free from direct sunlight, dust,drip, salt, oil smoke, water vapor, combustible gas and corrosive gas.
Altitude

If the altitude is equal or lower than 1000 meters, the AC drive can be used normally.

If the altitude is higher than 1000 meters, it is necessary to de-rate the AC drive. The ratio of derating the AC drive is 1 percent for every increase of 100 meters.

If the altitude is higher than 3000 meters, please contact our agents.

Temperature

-10℃ to +40℃.

If the ambient temperature is 40℃ to 50℃, please keep good ventilation and take the action of derating: The ratio of derating the AC drive is 3 percent for every increase of 1℃.

HumidityLess than 95%RH, without condensing.
VibrationLess than 0.6g
Storage temperature-25℃~+65℃

 

 

1. Wide voltage range input

Power voltage: -15% - 10%, 47 Hz - 63 Hz; provided with under-voltage underclocking output function that extends the applicable range of power voltage to -30% (e.g. extending the applicable range of a 380 V VFD to 266 V - 440 V);

2. High disturbance resistance

Pulse group tests: ± 4,800 V

Static (air discharge): 8,000 V

Static (contact discharge): 6,000 V

Provided with EMI circuit + lightning protection design

3. Phase-phase and phase-to-earth short circuit protection

Any phase-phase short circuit protection < 8uSec U, V and W phase-to-earth short circuit protection;

4. Anti-corrosion treatment

8 µm nickel plating, and three layers of British conformal coating for key parts;

5. Power source of control signals:

External power supply of +10 V and +24 V, both provided with short circuit protection.

The +10 V power supply is provided with a current output of 30 mA.

The +24 V power supply is provided with a large current output of 200 mA

6. Overload capacity

The Type G VFDs of all series have an overload capacityof one minute under 150% of overload, while for Type L, one minute under 120%.

7. Comprehensive configuration

Supports an extended relay board: four extended relays (T3 - T4) and one Y terminal (Y3), supporting up to 6 relay outputs; and for CDE360-4T30G/37L and lower types, a built-in braking unit is provided.

8. Revs tracking

Smooth tracking that is successfully completed in one time is guaranteed, whether the motor is revolving forward or backward, and the revolving speed high or low.

9. Non-stop operation during instantaneous power failure

On the occasion of a municipal power failure, the VFDs can remain operatingbased on their energy feedback; the low voltage ride through (LVRT) can be realized.

10. Low-frequency current output is highly close to sine with large torque.

0.5 Hz, the motor can output 100% of its rated torque.

 

Hot Products

New CDE601 mini series high performance variable frequency drive inverter for general purpose ...
Easy operation variable frequency inverter single phase 220V 1.5kw vfd for pump CDE500Y VFD for ...
0.75kw-15KW sensorless vector control frequency inverter/ac drives/variable speed drive (built-in ...
Inverter 220V 1.5kw for spindle motor 2-Phase VFD CDE500Y VFD for oilfield Description Canworld ...
380V 3 phase 1 hp ac drive vfd similar to Delta CDE500Y VFD for oilfield Description Canworld ...
ac drive for chemical industry mini electric motor frequency inverter for printing Description ...