Backup Battery Servo Parking Boom Gates IP54 Aluminum 1.5mm Arm Thickness

Contact Us

[China]

Trade Verify

Address: 1st Floor, Zhigu, No. 2-10, South jinlong Avenue, Shahu Community, Biling Street, Pingshan District, Shenzhen, China

Contact name:Keira

Verified Suppliers

Country/Region	china
City & Province	shenzhen guangdong
Categories	Other Access Control Products

Backup Battery Servo Barrier Gate Automatic Boom Barrier IP54

Quick Details:

1. The gate automatically open when the power is off, no clutch design, no need human intervention

2. The use of Single Compression Balance Spring device, good regulation, no noise, indefatigable, not easily broken, safe and reliable

3.Arm opening angle can be adjusted from 60 to 90 degrees, 10 degrees resolution, suitable for eaves prominent place to install.

Parameters

DZ-138 barrier gate	V06T	V09T
Max Boom Length and Diameter	2500mm, Ф75mm	3000mm, Ф75mm
Open/Close Time	0.6sec	0.9sec,2.5sec,4.5sec
Power Supply	24/100/240VAC,50/60Hz	24/100/240VAC,50/60Hz
Power Consumption	max.150W	100w
Machine Case	Varnished 2.0mm steel plate	Varnished 2.0mm steel plate
Machine Case Size(WDH)	342312959mm	342312959mm
Net Weight	43kg	42.6kg
Operating Temperature Range℃	-45℃~+85℃	-45℃~+85℃
Driving Method	Servo motor	Servo motor
Protection System(IP)	54	54
Insulation Class	F	F
Relative Humidity	≤90%	≤90%
Motor No-load Speed	3000r/min	3000r/min
Remote Control Distance	≤100m (open, sunny weather)	≤100m (open, sunny weather)
Output Torque	1.2N.M*140=160N.M	0.86N.M*140=120N.M
Running Noise＜	45dB	45dB
Surface Treatment	Outdoor metal powder electrostatic spraying	Outdoor metal powder electrostatic spraying
DZ Controller
Voltage(±10%)	100-240 volt	100-240 volt
Frequency(Hz)	50-60	50-60
Max Power Consumption(watt)	8	8
Fuse	F5AH	F5AH
Control Voltage	24V DC/max.3000mA	24V DC/max.3000mA
Input-end Number	8	8
Open Collector Output Number	2	2
Zero Level Reversal Relay Number	3	3
Operating Temperature Range℃	-45℃~+85℃	-45℃~+85℃
Protection System(IP)	20	20
Weight(gram)	450gram	450gram
Dimension	mm(L-W-H)	15812655

Operation Time and Boom Length Configuration Parameter.

Boom Type(meter)	Operation Time(seconds)	Boom Height(meter)
Fast speed boom≤2.5	0.6	0.83
Fast speed boom≤3	0.9	0.83
Common straight boom≤4.5	2.5	0.83
Common straight boom≤6	4.5	0.83
80*45mm 90°folding boom≤3	1	0.83
80*45mm 90°folding boom≤3.5	2.5	0.83
80*45mm 90°folding boom≤5	5	0.83
80*45mm 180°folding boom≤3	1	0.83
80*45mm 180°folding boom≤4	2.5	0.83
80*45mm 180°folding boom≤5	4.5	0.83
100*45mm 2 fence boom≤3.5	2.5	0.83m, small vertical boom is 0.8m, landing boom is 0.9m
100*45mm 2 fence boom≤5	6	0.83m, small vertical boom is 0.8m, landing boom is 0.9m
100*45mm 3 fence boom≤3	3	0.83m, small vertical boom is 1.5m, landing boom is 1.6m
100*45mm 3 fence boom≤4	6	0.83m, small vertical boom is 1.5m, landing boom is 1.6m

Maintenance

1)Keep the barrier gate clean.

2)Check the joints every month in case of any loose parts.

3)Check the spring elasticity after barrier gate running 30,000times

4)Check the easily worn-out parts(like spring,limit switch)every half year and renew it.

5)Remote control distance will be shortened or not work in cases like big object screening, battery run out.extreme weathers.

FAQ:

1. When barrier finish closing, why does the arm open itself slowly?

the spring is too tight, you need release the spring a little, then test it again.
see whether the main crank touch the triangle tightly or not, if tightly, adjust it.
reset the balance position and the electrical limit switch.

2. Why does the controller panel operate with "Di Di Di" abnormal noises?

As for this, it means the resistance on controller board is broken, if you have professional tools to check,
then replace that broken resistance, if not, replace that controller panel.

3. Why does the barrier finish half operation of opening and closing?

If uses our controller panel, you only need to find resistance R37 on controller panel, and repalce it is ok.

4. When barrier closed, why is there a 5 degree angle of inclination?

5. When barrier finish open, but it closes itself without any order control, what's the problem?

To check the loop cable first, because the loop cable maybe brokem
To check the motor sensor, if it is not set well, then reset it in the middle between two holes on sensor rod.

6. Why does the arm wave a lot when opening and closing?