All plastic with 1.5 meter height slide and barriers outdoor
playground for small venue with unusual colors TQ-QS008
We all know that children's play equipment will have different
degrees of wear after using for a period of time. This kind of wear
will affect the second-hand sales of equipment, and some even can
not be used normally, there is a huge danger. So how do we deal
with wear and tear? Below, we introduce you.
(1) Pre-wear period of amusement equipment
First of all, the new amusement equipment wears out very quickly
when it is used, and as the running-in progresses, the rough
appearance will be smoothed. At this time, the wear speed is
reduced, and the running-in period ends. This period of time is
called the pre-wear period.
At this time, the operator will consciously use the minute wear
during this period to create conditions for the stable operation of
normal operation. During this period, regarding the non-running
equipment, the principles of load shedding, deceleration, and
reasonable operation should be abide by, and the smooth oil with
low viscosity should be added as much as possible. In addition, in
order to shorten the running-in period, it is possible to select
the appropriate leading technology, etc., and use the lubricating
oil that meets the quality requirements to improve the utilization
rate of the equipment.
(2) During the stable running-in period of the amusement equipment
During this period of normal operation, after the amusement
equipment is run-in, the conflicting surface is hardened and the
wear is slow and stable. In the later period of this period, due to
metal fatigue, the wear is relatively accelerated, but it still
works continuously. When approaching the fatigue limit of metal,
the operator must perform regular forced repairs on the equipment
to prevent the equipment from causing major accidents due to
excessive wear. .
(3) During the intense wear of amusement equipment
During this period, because the metal outer surface of the
amusement equipment reached the fatigue limit at all, the conflict
conditions were greatly changed (such as a sharp rise in
temperature, a significant change in the surface metal arrangement,
a slight change in the shape of the microscopic, an increase in the
gap, a deterioration in the smooth condition, etc.) ), the wear
rate of the equipment is sharply increased, the mechanical
efficiency is reduced, the precision is lost, abnormal noise and
vibration occur, and the mechanical properties of the data are
changed, eventually causing the parts to fail and must be repaired.
At this time, if it is forced to operate normally or even at a high
load, a major accident will inevitably occur.
So, what is the correct way to find out that children's play
equipment is worn out?
1. Lubrication. If the wearing parts of the amusement equipment are
lubricated, the friction generated between the parts can be
reduced, and the wear can be reduced;
2. If there is an error in the installation position of the
children's play equipment, wear will occur. Therefore, we remind
operators to increase the accuracy of the installation in order to
reduce wear and often check.
3. Finally, there is a point that some dust can easily cause wear
and tear in children's play equipment, and some can cause rust and
cause more problems. Therefore, it is also very important to keep
the amusement equipment clean.
Measurements (mm) | 480x450x320cm(L*W*H) |
Safety Area (mm) | 780*750cm(L*W) |
Certificate | ISO9001, SGS,CE |
Modules | Roofs, slides, plastic panels, stairs, decks, tubes and posts,
climbing. |
Material | A. Plastic parts: Imported LLDPE |
B. Post: National standard galvanized steel pipe |
C. Metals: Galvanized |
D. Deck, stair, bridge: Steel with plastic covered |
E. Fasteners: 304 stainless |
(Different material is available at your demand. ) |
Advantage | a.Anti-UV |
b.Anti-static |
c.Security |
d.Environmental protection |
e.Color is not easy to fade |
Installation | 2 day (2 persons) |
Falling Height (mm) | 2200 |
Age Range | 3--12 age |
Capacity | 10-20 persons |
Apply to | Amusement park, kindergarten, preschool, residential area. |
Packing | Standard export packing |
Plastic parts: Bubble bag and pp film; |
Iron parts: Cotton and pp film |
Delivery Volume:6CBM |
Use Life | 7-10 years |
Remark | 1.Please check the screws and other catchers regularly to assure
the firm structure. |
2.Please make sure that all the kids play with adult supervision. |
3.Blunt objects and acid corrosive liquor are forbidden. |