Home Companies Shenzhen Wance Testing Machine Co., Ltd.

ASTM D2241 Standard PVC Pipe Testing Equipment For Flattening Test ETM104B

Contact Us

[China]

Trade Verify

Address: No.9, Shuiku Road, Tangwei, Guangming District, Shenzhen 518132, China

Contact name:Leo

Shenzhen Wance Testing Machine Co., Ltd.

Verified Suppliers
  • Trust
    Seal
  • Verified
    Supplier
  • Credit
    Check
  • Capability
    Assessment

ASTM D2241 Standard PVC Pipe Testing Equipment For Flattening Test ETM104B

Country/Region china
City & Province shenzhen guangdong
Categories Steering System

Product Details

Electromechanical universal testing machine 10kN class 0.5 plastic pipe flattening test ASTM D2241 ETM104B

 

 

Typical specimens: Small components, reinforced plastics, metals, wire, composites, elastomers, wood products, textiles, biomaterials, paper products, adhesives, foam, consumer products

New Features

  • Non-clutched drives, rated for full speed at maximum force
  • Compact design saves lab space
  • Wider test width

 

High Quality at affordable price

 

  • Pre-loaded ball screws and heavy duty bearings assure long life with zero backlash as well as linear low force and through zero performance. The result is accurate and repeatable measurements that truly represent the specimen characteristics rather than load frame deficiencies
  • Fully-protected lead screw covers provide longer life and greater operator protection
  • Easy-to-clean aluminum column covers with chamfered corners to facilitate access to the test area. T-slots are built in for simple, convenient attachment and positioning of testing accessories
  • High-speed, low vibration, world-class, maintenance-free, imported AC servo motor and servo controller
  • Photoelectrical encoder built in servo motor system is for position measurement of crosshead
  • Built-in bidirectional load cell is assembled in the middle crosshead to prevent any collisions and simple to perform compression or tension tests
  • Dual action over-travel limits on all frames provide the highest level of safety and meet all international standards
  • Remote control keypad facilitates test operation
  • Full one-year warranty on parts and labor
  • Free software upgrading

 

ASTM D2241 - Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDRSeries)

1. Scope
1.1 This specification covers poly(vinyl chloride) (PVC) pipe made in standard thermoplastic pipe dimension ratios and pressure rated for water (see appendix). Included are criteria for classifying PVC plastic pipe materials and PVC plastic pipe, a system of nomenclature for PVC plastic pipe, and requirements and test methods for materials, workmanship, dimensions, sustained pressure, burst pressure, flattening, and extrusion quality. Methods of marking are also given.
1.2 The products covered by this specification are intended for use with the distribution of pressurized liquids only, which are chemically compatible with the piping materials. Due to inherent hazards associated with testing components and systems with compressed air or other compressed gases, some manufacturers do not allow pneumatic testing of their products. Consult with specific product/component manufacturers for their specific testing procedures prior to pneumatic testing.
NOTE 1—Pressurized (compressed) air or other compressed gases contain large amounts of stored energy which present serious safety hazards should a system fail for any reason.
1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 
1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.5 The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. A specific precautionary statement is given in Note 7.

 

Flattening—Flatten three specimens of the pipe, 2 in. (50 mm) long, between parallel plates in a suitable press until the distance between the plates is 40 % of the outside diameter of the pipe. The rate of loading shall be uniform and such that the compression is completed within 2 to 5 min. On removal of the load, examine the specimens for evidence of splitting, cracking, or breaking.

 

 

 

Specifications:

 

ModelETM104
TypeType B, dual column, table-top
Capacity10kN
Calibration standardISO 7500, Class 1 / Class 0.5
Force range0.2% ~ 100%FS / 0.4 ~ 100%FS
Force accuracy±1.0% / ±0.5% of reading
Force resolution1/500000FS
Position accuracy±0.50% of reading
Position resolution0.027μm
Crosshead speed0.001 ~ 500mm/min
Crosshead speed accuracywithin ±1.0% / ±0.5% of set speed
Crosshead travel1000mm
Test width420mm

Dimension

(WidthxDepthxHeight)

728 x 470 x 1520 (mm)
Power requirementSingle phase, 220±10% VAC, 50/60Hz, 400W
Weight150kg

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Hot Products

Electromechanical universal testing machine 10kN ISO 8067 Flexible cellular polmeric materials tear ...
Electromechanical universal testing machine 10kN ASTM D3330 Peel Adhesion of Pressure-Sensitive Tape ...
Electromechanical universal testing machine 10kN ISO 3386 foam Determination of stress-strain in ...
Electromechanical universal testing machine 10kN ISO 2439 Foam hardness indentation technique ...
Electromechanical universal testing machine 10kN class 0.5 plastic pipe flattening test ASTM D2241 ...
Electromechanical universal testing machine 10kN ASTM D5748 Protrusion Puncture Resistance of ...