Prolonged Drilling 12 1/4 Inch Drill , Mining Drill Bits For Drilling Requirements

Hard Rock Drill Bits In Various Sizes For Wide Range Of Drilling Requirements

 
Click here for catalogueTCI DRILL BIT.pdf

What is Hard Rock Drill Bits

Hard Rock Drill Bit - a drilling method that uses a roller bits. In roller-bit drilling, rock is cut by hard-alloy teeth projecting from rolling cutters, which rotate on the drill-bit bearings. Inturn, the drill bit rotates at a high rate, and presses against the bottom hole with a high axial force. The teeth of the rolling cutters roll over the bottom hole and, owing to the large stresses that develop in the area of contact between the teeth and the rock, cut the rock by crushing and chipping. As the hardness of therock increases, the rotation rate decreases and the axial force increases. Destroyed at the mine the rock is removed to the surface by air compressor, mud pump, or a combination of these methods.All bits the above are manufactured according to strict standards, set forth by the American Petroleum Institute (API). And classified according to characteristics set forth by the International Association of Drilling Contractors (IADC).

Application

Medium to Medium-Hard Formation

Application: For use in moderately abrasive consolidated formations with compressive strength ranging between 140 – 485 Mpa such as hard limestone, quartzite, granodiorite, and medium grade metamorphic formations

Cutting structure: These bits are characterized by moderately spaced conical inserts with medium projection. This configuration promotes good penetration rates in medium hard and moderately abrasive formations. Smaller carbide inserts are provided on the gage and inner rows or hard metal is deposited in the nose area to contain shell erosion and improve performance.

• Compression Strength: 20,000 – 70,000 psi
• Drilling Speeds: 60 – 100 rpm
• Jet Circulation: All sizes
• Weight on Bit (WOB): 2,500 – 7,000 lbs/in of bit diameter

Tricone drill bit is one of the main tools for blast hole and well drilling, mainly used for large-scale open-pit mining, such as open-pit coal mines, iron mines, copper mines and molybdenum mines, also the non-metallic mines. With the increasing in variety of type, it’s also widely used in quarrying, foundation clearing, hydrogeological drilling, coring, tunneling in railway transportation department and shaft drilling in underground mines. The rock breakage by the tricone bit which used in mine is working with both the impact of teeth and the shear caused by slippage of the teeth, which bring high rock breaking efficiency and the low operation cost.

CUTTING SELECTION GUIDE

Working theory of TCI tricone bit
 
The medium formation TCI tricone bits features aggressive chisel tungsten carbide inserts on the heel rows and inner rows. This design provides a fast drilling rate and added cutting structure durability in medium to medium hard for mations. The HSN rubber O-ring provides adequate sealing for bearing durability.
Tricone bit is connected with the drill stem and rotates along with it, and drive cones to pressed on the rock. Each cone rotates round the axis of its leg and three cones simultaneously revolve around the bit center. The tungsten carbide inserts on the cone shell cause the formation to spall under the weight on bit and the impact load of cone rotating, the debris will be discharged out to hole by compression air.
The medium formation TCI tricone bits features aggressive chisel tungsten carbide inserts on the heel rows and inner rows. This design provides a fast drilling rate and added cutting structure durability in medium to medium hard for mations. The HSN rubber O-ring provides adequate sealing for bearing durability.

 
Advantage:
1. Strictly select the material to ensure the reliable quality. Bad steel and tungsten carbide inserts won't be used.
2. Strictly act according to the ISO9001 standard, and control by full-scale inspection.
3. Sales and support people are highly trained in the latest rock drilling technology and can offer you expert advice on what products will best fit a specific end use application.
 
Tianying's Best Service
1. 365×24 Year-round Service,We are committed to year-round 24-hour service even during holidays.
1. Provide professional technical services, including products introduction, selecting and problem solution etc.
3. Within 35 Working Days Quick Delivery.
 
 
Our Company
Hunan Tianying Drilling Machine Manufacturing Co., Ltd, supplies tricone drill bits, which are widely used in mining drill. Products offers a complete line of tricone bits, which using the best raw material in the market. Reliable steel, tungsten carbide, bearing and lubrication system, size from 7 7/8”(85.7mm) to 26”(660.4mm) for use in all formations, Our Tricone Bits are with Sealed Bearing, Roller Bearing and Gage Protected which can ensure you can drill more meters.
 
 

Tianying's Best Service
1. 365×24 Year-round Service,We are committed to year-round 24-hour service even during holidays.
1. Provide professional technical services, including products introduction, selecting and problem solution etc.
3. Within 35 Working Days Quick Delivery.