Air Spring Triple Convoluted Goodyear 2B12-313/459 Firestone
W01-358-7808/313
Product Overview
OEM Number:W01-358-7808
Warranty:12 Months
Place of Origin:Guangdong,China
Product Name:Air Spring Triple Convoluted
Type:Suspension Spring
Firestone: W01-358-7808/313
Contitech: FD 330-22 364
Goodyear : 2B12-313/459
:578933350
Triangle:6319/4336
Airkraft:11506/3B-356
Brake & Wheel:M3533
EI Ride:8030170
Dayton:3547808
Leland:Sc2031
Navistar:554801C1
Hendrickson:S13157
Ridewell:1003587808C
SAF Holland:57007808
Truck stell:63640
Peerless:55000030
Contitech FD 330-22 364 Air Spring Technical Data
♦Cover Plate
Top Cover Plate Diameter:289mm
Bottom Cover Plate Diameter: 289 mm
♦Gas Hole/Air Inlet/Air Fitting
Gas Hole/Air Inlet:1/4NPT
♦Nut/Blind Nut
Top Cover Plate Screw (Nut) Tooth :4X3/8-16UNC
Bottom Cover Plate Screw (Nut) Tooth :4X3/8-16UNC
Screw Center Distance of Top Cover Plate : 158.8 mm
Screw Center Distance of Bottom Cover Plate : 158.8 mm
♦Rubber Bellows
Rubber Bellows MAX Diameter: 356 mm
The Working Stroke : 282mm
Warning and Tips
Maintenance of the air springs, Vehicle Check-List
- Check the air lines and devices of leakage and that they turns
freely.
- Check the bellows bearing for damage, correct fastening,
deformation, sharp edges.
- Check the shock absorbers for operation and impermeability as well
as tightness and bearing.
- Periodically, check nuts and bolts for proper torque. For specific
recommendations see manufacturer's manual.
- Check axle suspension, trailing arms and rods for wear.
- Check height control valve to see that it is functioning properly.
A properly maintained valve will save unneeded maintenance expense.
- Routine inspection of all of the above according to manufacturer's
instructions, will extend the life of your vehicle and reduce your
overall maintenance expense.
Air Spring Installation
- Before you start installing air springs, make sure you have all the
necessary tools and equipment to perform the repair safely.
- Familiarize yourself with the suspension on which you are
performing the repair by reviewing the manufacturers service guide.
- If you are in doubt about something, ask for assistance from a
qualified suspension specialist, the suspension manufacturer or the
air spring manufacturer; This can save you a lot of time and
aggravation later in the job.
Important tips to remember when installing a new unit
- Check levelling valve, linkage and transmission parts for wear and
damage and if necessary replace the damaged parts.
- Check that the shock absorber for leakages and take a shock
absorber test. A defective shock absorber must be replaced.
- Once the air lines are disconnected, check their entire length for
cracks or other damage. Replace worn parts.
- With the air spring removed, other parts of the air suspension
become more accessible. Check for wear or damage of the frame
hangers, trailing arm bushings, torque rods, the trailing arms and
the air spring mounts. When it is necessary, also replace parts.
- Check bearing for air spring bellow for external damage,
deformation, sharp edges and correct fastening.
- Before installing the new unit, clean the air spring mounting
plates to ensure proper attachment to the suspension.
- Always use new attaching bolts for the installation and observe the
tightening torques. Never use old bolts, because these can fall
out.
- Check the linkage of the levelling valve to see that it is
functioning properly. Under load, the linkage should move from the
neutral position up to the intake position. This lets air into the
springs, which brings the arm back to the neutral position. This
lets air into the springs, which brings the arm back to the neutral
position. That opens the exhaust valve, allowing air to escape
until the arm returns to the neutral position. Then check the
driving level.
Product Image Display