PV SPD 3Pole 1000V Surge Protection CE TUV 20ka 40kA Low-voltage
Protector Device
PV SPD 3Pole 1000V Surge Protection General:
1: Safety super wide electrical spacing and creepage distance, high
voltages withstand voltage, meet high altitude area use
requirement.
2: The Surge Protection Device (DC SPD) attempts to limit the
voltage supplied to an electric device by either blocking or
shorting current to reduce the voltage below a safe threshold.
3: No load current is considered; plug and pull design, can be
charged replacement, easy to maintain.
4: This device is connected in parallel on the power supply circuit
of the loads that it has to protect.
5: Built-in temperature control circuit technology, high safety
performance, no after flow.
6: This is the most commonly used and most efficient type of
overvoltage protection.
7: Indicates that the green color of the window is normal and any
red indicates failure. Clear and easy to distinguish.
8: The shell is made of PC flame retardant material, fire proof and
heat insulation.
9: Optional remote monitoring interface can be used for remote
monitoring.
10: Prevent lightning surge voltage in solar system (photovoltaic
power supply system)
11: High working voltages, high pass flow, high safety performance
and high stability.
PV SPD 3Pole 1000V Surge Protection Product Details:
| BRPV3 1000 |
SPD classification according to EN61643-31 | Type 2 |
SPD classification according to IEC61643-31 | Class II |
Max. continuous operating dc voltage
Ucpv | 1000V |
Nominal discharge current (8/20us)
In | 20kA |
Max. discharge current (8/20us)
Imax | 40kA |
Voltage protection level [(DC+/DC-)→PE]
Up | ≤4.0kV |
Response time
tA | ≤25ns |
Operating temperature range
Tu | -40℃-80℃ |
Operating state / fault indication | green / red |
Cross-section area (Min.) | 4mm2 |
Cross-section area (Max.) | 35mm2 |
For mounting on | 35mm Din rail |
Enclosure material |
Thermoplastic UL94-V0
|
Degree of protection | IP20 |
Order Code | B8010 |
Order code(With remote signal) | B8012 |
Technology characteristic:
PV SPD 3Pole 1000V Surge Protection Features:
- For surge protection of photovoltaic (PV) system.
- These units must be installed in parallel on the DC network in
order to be protected and to provide common and different mode
protection
- The core parts are metal oxide varistor components with high
discharge capacity.
- It is recommended to install it at both ends of the DC power
supply line (solar panel side and inverter side)/ converter side),
especially if the line route is external and long.
- Low residual voltage and quick response.
- The BRPV3-1000 Surge Protection are designed to protect against
lightning surge voltages in photovoltaic power supply networks.
- Reliable control.
- The BRPV3-1000 is available for the main operating voltages in
photovoltaic: 1000 Vdc.
- With remote signaling contact for control device.
- Fault indication via red mark in the inspection window.
- Protection mode: L+/L- – PE.
Working principle of product:
In the solar photovoltaic system, the inductive or capacitive
coupling voltage is caused by the lightning shock and the switching
operation of the upstream power supply system. Therefore, the surge
may damage the photovoltaic modules and inverters, which will cause
serious consequences for the operation of the photovoltaic system.
The photovoltaic lightning arrester is specially developed for this
purpose. The lightning protection module of the DC power supply,
once the high voltage, and endanger the insulation of the protected
equipment, the lightning arrester acts immediately, and the high
voltage impact current is directed to the earth, thus limiting the
amplitude of the voltage and protecting the insulation of the
equipment. When the overvoltage is gone, the arrester is restored
to its original state quickly, so as to protect the power
equipment.
Our Services:
• 17 years global leading profession manufacture of electrical
products surge arrester.
• All products will be well packed before shipping.
• Standard packaging, and you can also tell us your own
requirements on packaging.
• Faster delivery.
• Individually Tested Prior to Shipment.
Company profile:
Wenzhou Britec Electric Co.,Ltd is a company specialized in SPD
products for many years; Using the brand for many years exporting
of which it's experience enables Britec the ability to know
what customers need, what end users need. Top quality and best
services is our first and formost belief. welcome to cooperate
with us, welcome to join us!
Workshop show:
Certifications:
FAQ:
1. Who are we?
A: We are based in Yueqing, Zhejiang, China, start from 2003, sell
to Europe, South America, Mid East, Southeast Asia,
Africa.
2. How can we guarantee quality?
A: Always final Inspection before shipment;
3. What can you buy from us?
A: All kinds of SPDs.
4. Why should you buy from us not from other suppliers?
A: Focus on customer service always!
5. What services can we provide?
A: Accepted Delivery Terms: FOB, CIF, EXW
Accepted Payment Currency:USD, EUR, CNY;
Accepted Payment Type: T/T, L/C, PayPal;
Language Spoken:English, Chinese