|
[China]
Trade Verify
Address: No.20 Guanghua Street, Changzhou, Jiangsu, China 213003
Contact name:
Changzhou Smart Automation Motor Manufacturing Co., Ltd. |
|
Verified Suppliers
|
|
|
CW5045 24V - 50V DC 1.3A - 4.5A 2 Phase Mirco Stepping Stepper Motor Drivers
Characteristics:
1.DC power input type:24V~50VDC
2.Output current:1.3A-4.5A
3.Mircostepping:1(1.8º) 1/2 1/4 1/8 1/16 1/32 1/64 1/128 1/256
1/5 1/10 1/25 1/50 1/125 1/250
4.Protect form :Overheated protect, lock automatic half current
,error connect protect
5.Dimensions:118mm×76mm×33mm
6.Weight:<300g.
7.Working environment:Temperature-15～40℃Humidity<90.
I/O Ports:
1.VCC+:DC power positive pole
Note:Must guard against exceeding 50V, so as not to damage the
module
2.GND:DC power cathode
3.A+ A-:Stepping motor one winding
4.B+ B-:Stepping motor other winding
5.PUL+ PUL -:Stepping pulse input+5V (Rising edge effective,rising
edge duration >10μS)
6.DIR + DIR-:Stepping motor direction input, voltage level touched
off,high towards, low reverse
7.ENA+ ENA-: motor free
NOTE:
1.When ambient temperature is high or working current over 2.7A, fix
the module on big metal shell , or use axle flows fan dispels the
heat, to make the module run reliably for a long time.
2.Half current automatically: if control machine not send out
signal in half second, driver enter half current state of
automatically for electricity saving, the phase current of the
winding of the electric
3.The fault phase is protected: When the double-phase electrical
machinery is connected with driver, users are apt to connect the
phase by mistake, thus would damage the driver seriously. The
protecting circuit is within this driver, when users connect by
mistake, the driver will not be damaged, but the electrical
machinery runs abnormally, shake , and output is small.Please check
whether the wiring of electrical machinery is a mistake.
Switch Choice: (“ON=0,OFF=1”)
1.Microstepping choice:
SW5 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 1 | 1 | 1 |
SW6 | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 1 |
SW7 | 0 | 0 | 1 | 1 | 0 | 0 | 1 | 1 | 0 | 0 | 1 | 1 | 0 | 0 |
SW8 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 1 | 0 | 0 | 0 | 0 | 1 | 1 |
Micro | 1/2 | 1/4 | 1/8 | 1/16 | 1/32 | 1/64 | 1/128 | 1/256 | 1/5 | 1/10 | 1/25 | 1/50 | 1/125 | 1/250 |
2.Current choice:
SW1 | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 1 |
SW2 | 0 | 0 | 1 | 1 | 0 | 0 | 1 | 1 |
SW3 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 1 |
Current(A) | 1.3 | 1.8 | 2.3 | 2.7 | 3.2 | 3.7 | 4.2 | 4.5 |
3.Full current or half current choice:
SW4:0＝Full current,1＝half current
4.Pulse choice:
In the driver has a jump
5.installation dimension
