|
[China]
Trade Verify
Address: NO.288,YOUYI ROAD ,XI SHAN DISTRICT,WUXI CITY,CHINA
Contact name:Gao Ben
JIANGSU MITTEL STEEL INDUSTRIAL LIMITED |
|
Verified Suppliers
|
|
|
Cold Rolled Stainless Steel Coils AISI 430 Matte Polished NO.4 Finish SUS430 Stainless Steel Strip
Introduction
Key Properties
Composition
Mechanical Properties
Physical Properties
Grade Specification Comparison
Possible Alternative Grades
Corrosion Resistance
Heat Resistance
Heat Treatment
Welding
Machining
Fabrication
Applications
Fe, <0.12% C, 16-18% Cr, <0.75% Ni, <1.0% Mn, <1.0% Si, <0.040% P, <0.030% S
Stainless steel grade 430 is a non-hardenable steel containing straight chromium, and belongs to the ferritic group of steels. This steel is known for its good corrosion resistance and formability, coupled with practical mechanical properties. It can be used in certain chemical applications due to its resistance to nitric acid.
Grade 430F stainless steel is usually provided in bar form to be used in automatic screw machines.
Grade 434 has similar properties as grade 430, although it is a molybdenum-bearing version. The molybdenum content enhances its corrosion resistance.
The following sections will provide the key properties of grade 430 stainless steels coil, sheet and plate - covered under ASTM A240/A240M.
The chemical compositions of various elements of grade 430 stainless steels are tabulated below.
Table 1 – Chemical compositions of grade 430 stainless steels
| GradeN | C | Mn | Si | P | S | Cr | Mo | Ni | N | |
| 430 | min. max. | - 0.12 | - 1 | - 1 | - 0.04 | - 0.030 | 16 18 | - | - 0.50 | - |
| 430F | min. max. | - 0.12 | - 1.25 | - 1 | - 0.06 | 0.15 - | 16 18 | - | - | - |
The mechanical properties for grade 430 stainless steels are listed in the table below.
Table 2 - Mechanical properties of grade 430 stainless steels
| Grade | Tensile Strength (MPa) min | Yield Strength 0.2% Proof (MPa) min | Elongation (% in 50mm) min | Hardness | |
| Rockwell B (HR B) max | Brinell (HB) max | ||||
| 430 | 483 | 310 | 22 | 85 | 183 |
| 430F | 552 typical | 379 typical | 25 typical | - | 262 |
Table 3 - Physical properties of grade 430 stainless steels in the annealed condition
| Grade | Density (kg/m3) | Elastic Modulus (GPa) | Mean Coefficient of Thermal Expansion (μm/m/°C) | Thermal Conductivity (W/m.K) | Specific Heat 0-100°C (J/kg.K) | Electrical Resistivity (nΩ.m) | |||
| 0-100°C | 0-315°C | 0-538°C | at 100°C | at 500°C | |||||
| 430 | 7750 | 200 | 10.4 | 11.0 | 11.4 | 26.1 | 26.3 | 460 | 600 |
| 430F | 7750 | 200 | 10.4 | 11.0 | 11.4 | 26.1 | 26.3 | 460 | 600 |
A comparison of grade specifications for 430 stainless steels is given in the following table.
Table 4 - Grade specifications for 430 stainless steels
| Grade | UNS No | Old British | Euronorm | Swedish SS | Japanese JIS | ||
| BS | En | No | Name | ||||
| 430 | S43000 | 430S17 | 60 | 1.4016 | X8Cr17 | 2320 | SUS 430 |
| 430F | S43020 | - | - | 1.4104 | X12CrMoS17 | 2383 | SUS 430F |
Suitable alternative grades that can be chosen instead of grade 430 stainless steelgrades that can be chosen instead of grade 430 stainless steel are listed in the table below.
Table 5 - Possible alternatives to grade 430 stainless steel
| Grade | Reasons for choosing 430 |
| 430F | Higher machinability than 430 is needed in bar product, and reduced corrosion resistance is acceptable |
| 434 | Better pitting resistance is required |
| 304 | Slightly higher corrosion resistance is needed, together with greatly improved ability to be welded and cold formed |
| 316 | Much better corrosion resistance is needed, coupled with greatly improved ability to be welded and cold formed |
| 3CR12 | Lower corrosion resistance is acceptable in a cost-critical application |
All ferritic grades, such as stainless steel grade 430, have excellent stress corrosion cracking resistance. Grade 430 has good corrosion resistance to numerous substances, such as certain organic acids and nitric acid. The corrosion resistance is maximized in well-polished or buffed condition. Its pitting and crevice corrosion resistance is quite similar to that of grade 304. 430F is a high-sulfur free machining grade, and therefore the resistance to pitting and crevice corrosion is comparatively lesser than those grades that are non-free machining.
Stainless steel grade 430 is capable of resisting oxidation up to 870°C (1598°F) in intermittent usage, and up to 815°C (1499°F) in continuous usage. At room temperature, it has the tendency to become brittle, especially when it has been heated for a long time in the 400-600°C (752-1112°F) range. This issue can be overcome with annealing.
Solution annealing can be performed by heating stainless steel grade 430 to 815 - 845°C (1499-1553°F). Then it has to be slow furnace cooled to 600°C (1112°F) and followed by air-cooling in a quick manner - as slow cooling between 540 and 400°C (1004 and 752°F) tends to cause embrittlement.
For sub-critical annealing, heating should be performed to 760-815°C (1400-1499°F), followed by air-cooling or water quenching.
This stainless steel cannot be hardened by thermal treatment.
To perform any welding, stainless steel grade 430 has to be pre-heated at 150-200°C (302-392°F). In case of embrittlement in the welded metal, the particular area can be post-weld annealed at 790-815°C (1454-1499°F); however grain refinement will not happen.
It is recommended that grade 430, 308L, 309 or 310 filler rod should be used based on the application.
The machinability of stainless steel grade 430 is a lot easier than standard austenitic steels such as grade 304 - but there is a chance for galling. Lightly drawn bars are easier to machine than bars in the annealed condition. Grade 430F is easy to machine.
Stainless steel grade 430 has a low work hardening rate which enables easy bending and forming. The low ductility rate, however, makes it difficult to perform very rigorous operations. It is possible for grade 430 wire to handle rigorous cold heading. Sub-critical intermediate annealing may be required for extreme cold working.
The following are the applications for stainless steel grade 430:
The key application of grade 430F is in repeatedly used machined parts.
