Shanghai Haosteel Co., Limited |
Verified Suppliers
|
|
Aluminum Round Bar 1050 1060 1070 1100 3003 3004 5052 5005 5083 5754 Full Grades
Description:
The 1050 aluminum bar is used in reflector, decoration, chemical
industrial container, etc.
The 5083 belongs to al-mg-si alloy, which is widely used,
especially in the construction industry. It is the most promising
alloy.
Good corrosion resistance, good weldability, good cold working
ability and medium strength.
The main alloy element of 5083 is magnesium, which has good forming
performance, corrosion resistance, weldability and moderate
strength. It is used for manufacturing plane fuel tank, oil pipe,
sheet metal parts of traffic vehicles and ships, instruments,
street lamp bracket and rivets, hardware products, electrical
enclosure, etc.
Specification:
Item | Aluminum Rod /Aluminum Alloy Bar |
Standard | ASTM AISI, SUS, EN, JIS, DIN, GB ASME |
Other Material | 1060, 1050, 1070, 1100, 3003, 3004, 5052,5652, 5154, 5254, 5454, 5083, 5086, 5056,5456, 2024, 2014, 6061, 6063. etc |
Surface | Mill finish,polished,anodizing,brushing,sand blasting,powder coating,etc |
Diameter | 2~800mm |
Length | 1m,2m,3m,5.8m,6m,or as required |
Temper and Futures:
Code | Name | Description and Application |
F | Free-machining State | Applicable to products that have no special requirements for work hardening and heat treatment conditions during the molding process. The mechanical properties of the product are not specified. |
O | Annealed State | Suitable for processed products that have been fully annealed to obtain the lowest strength. |
H | Work Hardening State | Applicable to products that increase strength by work hardening. The product can be subjected to additional heat treatment after the work hardening can be passed through (or not). The H code must be followed by two or three Arabic numerals |
W | Solution Heat Treatment State | An unstable state, only applicable to alloys that are naturally aged at room temperature after solution heat treatment. This state code only indicates that the product is in the natural aging stage. |
T | Heat treatment state (different from F, O, H state) | Applicable to products that have been stabilized after (or not subjected to) work hardening after heat treatment. The T code must be followed by one or more Arabic numerals. |
Subdivision status of the H code:
Add two two-digit numbers (called HXX status) after the letter H,
or three Arabic numerals (called HXXX status) to indicate the
subdivision status of H. The first digit after H indicates the
basic handler for obtaining this state, as follows:
H1—Simple work hardening state. It is suitable for the state where
the required strength is obtained only by work hardening without
additional heat treatment.
H2—The state of work hardening and incomplete annealing. It is
suitable for products that have been subjected to incomplete
annealing after the degree of work hardening exceeds the
requirements of the finished product, so that the strength is
reduced to the specified index.
H3—The state of work hardening and stabilization treatment. It is
suitable for products which have been subjected to low-temperature
heat treatment after work hardening or whose mechanical properties
have been stabilized due to heat during processing. The H3 state is
only applicable to alloys that gradually age soften at room
temperature (unless stabilized).
H4—The state of processing and hardening paint treatment.
Applicable to work hardening, after painting, resulting in
incompletely annealed products.
3.2, the second digit after H indicates the degree of work
hardening of the product. The number 8 indicates a hard state. The
O state represents a fully soft state. For the state between the O
state and the HX8 state, a number from 1 to 7 should be added after
the HX code to indicate that the addition of the number 9 after the
HX indicates a superhard state that is harder than the HX8 work
hardening.
Product Show:
Application:
1. Aviation aluminum.
2. building material.
3. Architectural appearance ,outdoor design.
4. Indoor decoration: ceiling,, picture frame,etc.
5. Furniture, cabinet.
6. Elevator,lift,electric lift.
7. Car interior decoration.
8. Indoor decorations
9. Household appliances: refrigerator, microwave oven, audio
equipment, etc.
10. Aerospace and military aspect,aircraft manufacturing, the
Shenzhou spacecraft series, satellite, etc.
11. Part and mound making.