JIANGSU MITTEL STEEL INDUSTRIAL LIMITED |
Verified Suppliers
|
|
EN 1.4529 / 926 / UNS N08926Stainless Steel Plates Sheets and Coils Custom Cutting
Quick Informations
Products Name | 1.46529 / 926 Stainless Steel Plate | Standard | ASTM EN DIN JIS GB |
Thickness | 0.4 - 50.0mm | Surface | 2B NO.1 BA NO.4 8K |
Standard Size | 1000*2000mm 1219*2438mm 1500*6000mm | Service | Cutting, surface processing |
More Informations of our Products
Item | Stainless Steel Plates / Stainless Steel Sheets |
Main Grades | 201, 202, 301, 304, 304L, 310S, 309S, 316, 316L, 321, 409L, 410, 410S, 420, 430, 904L, etc. |
Thickness | 0.4mm-40mm |
Stock Thickness | 0.4mm 0.5mm 0.6mm 0.8mm 1.0mm 1.2mm 1.5mm 2mm, 2.5mm, 3mm, 3.5mm, 4mm, 4.5mm, 5mm, 5.5mm, 6mm, 7mm, 8mm,10mm,12 - 40mm |
Width | 1000mm 1219mm 1500mm or cutting any size as request |
Standard size | 1000*2000mm 1219*2438mm 1500*6000mm 2000*6000mm |
Finish | 2B, BA, No. 1, No. 4, mirror, brush, hairline, chequered, embossed, etc. |
Package | wooden pallets and waterproof paper |
EN 1.4529 stainless steel is a superaustenitic (highly alloyed) stainless steel formulated for primary forming into wrought products. Cited properties are appropriate for the solution annealed (AT) condition. 1.4529 is the EN numeric designation for this material. X1NiCrMoCuN25-20-7 is the EN chemical designation.
It has a moderately high tensile strength and a moderately high ductility among wrought superaustenitic stainless steels.
The graph bars on the material properties cards below compare EN 1.4529 stainless steel to: wrought superaustenitic stainless steels (top), all iron alloys (middle), and the entire database (bottom). A full bar means this is the highest value in the relevant set. A half-full bar means it's 50% of the highest, and so on.
1.4529 is characterized by:
Werkstoffnummer | 1.4529 |
Alloy | Alloy 926 |
Alloy 6XN | |
EN short name | X1 NiCrMoCuN25-20-7 |
UNS | UNS N08926 |
UNS N08367 | |
Registered Tradenames | SixMo® |
Ultra 6XN® | |
AL-6XN® | |
Cronifer 1925hMo® | |
Standards | EN 10028-7 |
EN 10088-2 | |
VdTÜV Werkblatt | 502 |
ASTM / ASME | ASTM A240/ B688/ B625 |
ASME SA24/ SB688/ SB625 |
1.4529 is mainly in following applications:
C | Si | Mn | P | S | Cr | Ni | Mo | Cu | N |
0-0.02 | 0-0.5 | 0-1.0 | 0-0.03 | 0-0.005 | 20,0-21,0 | 24.5-25.5 | 6.0-6.8 | 0.8-1.0 | 0.18-0.2 |
The material is hot formed within a temperature range of 1200 and
900 ° C and afterwards quenched rapidly in water or air.
The annealing takes place at 1200 ° C.
After hot forming, heat treatment for optimum corrosion resistance
is recommended.