Active Member
|
[China]
Address: Fuyong Xinhe Sanqu, 7 Xiang 12 Hao 102, Bao'an, Shenzhen, Guangdong, China
Contact name:Su Zhongqiu
Shenzhen Wanbo Hi-Tech Co., Ltd. |
|
|
Desktop 6 Heads SMT Assembly Machine Remote Technical Support
JUKI KE-2070 Pick And Place Machine Remote technical support of equipment
Multifunctional SMT Placement Machine 6 Heads For LED Power Driver / IC Chip
Juki KE-2070L SMT Machine Suitable for high-speed placement of small components
Used Juki KE-2070 smd equipment 23300CPH laser identification/condition
6 suction nozzles JUKI2070 SMT Assembly Machine Fast Speed For 1.2m PCB LED Strip
Used Juki KE-2070 Smd assembly machine Paste Bridge pile Convex lens on PCB
Shenzhen Wanbo High-tech Co., Ltd. has a JUKI senior engineer team with rich maintenance experience, specializing in providing JUKI series placement machine software and hardware maintenance and troubleshooting. It mainly includes JUKI laser head, CPU motherboard SUB-CPU board, drive board X/Y/Z/T axis driver, head board, image control card, I/O board, JUKI servo motor, camera, display touch screen, servo motor and other maintenance and replacement services. The company's fees are reasonable, the warehouse accessories are sufficient, the maintenance cycle is short, the one-time repair success rate is high, and the Pearl River Delta region can provide door-to-door installation, commissioning, maintenance and maintenance.
Perform this operation only after youperform inspections such as checkingof the main air pressure (0.5 Mpa) andchecking to see if there is no foreignsubstance around the ATC
Check to see if there is no foreignsubstance inside the machine
beforeproduction.
Be sure to warm up the system afterholidays or in cold climates (it
takesapproximately 10 minutes).
when you change a PwB type to beproduced, you have to adjust
theconveyor to the size of the PWB.
when the initial setup conditions of themachine change due to cleaning of thenozzle or change of the reference pinposition, set the "Machine setup" itemsagain.(Refer to Section 4.4 "Machinesetup" of the "Operation Manual ll.")
Refer to Section 4.1 "Database" of the"Operation Manual ll."
lf any problem occurs during PWBplacement:
for example, the PwB position is shiftedfrom the regulated position
or the
centering function fails, correct theproduction program on the
"ProgramEditor" menu.You can correct a part ofcomponent data on the
"Production"menu also.
Refer to Chapter 5 "Daily maintenance"of the "Operation Manual ll."
| Model name | High speed placement machine KE-2070M/L/E |
| Substrate size | M substrate (330×250mm) ○ l For substrate (410×360mm) ○ E substrate (510×460mm) ○ |
| Element height | 6mm specifications ○ 12mm specifications ○ 20mm Specifications _ 25mm Specifications _ |
| Component size | Laser identification 0402 (imperial 01005) chip ~ 33.5mm square element Image recognition 1.0×0.5mm~33.5mm square element |
| Component placement speed | Optimal conditions 0.155 sec/chip (23300CPH) IC Component 4600CPH* |
| Component placement accuracy | Laser recognition ±0.05mm Image recognition ±0.04mm |
| Component placement type | Up to 80 types (converted to 8mm belt) |
| power supply | Three-phase AC200~415V |
| Rated power | 3KVA |
| Use air pressure | 0.5±0.05Mpa |
| Air consumption | (Standard status) 345L/min |
| Device size (W×D×H) | M substrate 1,400×1,393×1,455mm L substrate 1,500×1,500×1,455mm E substrate 1,730×1,600×1,455mm |
| weight | 1530kg |
Accessories include: all kinds of original, domestic nozzles, FEEDER, boards, lasers, solenoid valves, inductors,
cylinders, tank chains, etc.), laser maintenance, board maintenance and so on.
