|
[China]
Trade Verify
Address: Room 101, 1st Floor, No. 6, Third Street, Pingshan Industrial Zone 511495, Shibi Street, Panyu District, Guangzhou, China
Contact name:Zoe Zou
Sinuo Testing Equipment Co. , Limited |
|
Verified Suppliers
|
|
|
IEC60598-1 IPX1~4 Vertical Water Drip And Spray Water Ingress Protection Test Chamber
Standard For IPX1~4 Vertical Water Drip And Spray Water Ingress Protection Test Chamber:
IEC 60529 -2013 “Degrees of protection provided by enclosure (IP code)” IPX1, IPX2, IPX3and IPX4
IEC 60598-1-2017 “Luminaries-Part1: General requirements and tests”
Application For IPX1~4 Vertical Water Drip And Spray Water Ingress Protection Test Chamber:
To verify the protective performance of the enclosure for electronic and electrical products, automobiles, motorcycle parts, household appliances, seals and lamps under water dripping at degree IPX1 & IPX2 and water spraying and splashing at degree IPX3 & IPX4.
Technical Parameters For IPX1~4 Vertical Water Drip And Spray Water Ingress Protection Test Chamber:
| IPX1 & IPX2 | |
| Chamber Size | Inner size: WDH=900×900mm×1050mm Outer size: WDH=1350×1150mm×1750mm |
| Drip Area | WD=600×600mm, other sizes can be customized |
| Drip Height | 200mm distance of the needle to the sample is achieved by adjusting the height of the turntable or raising the specimen |
Drip Speed (Water Flow) | 1+0.50mm/min or 3+0.50mm/min adjustable |
| Needle Pinhole Aperture | Φ0.4mm |
| Drip Hole Spacing | 20mmx20mm |
| Drip Box Position | Located at the top of the inner chamber, fixed |
| IPX3 & IPX4 | |
| Oscillating Tube | R400mm, R200mm is optional, made of stainless steel |
| Needle Pinhole Aperture | Φ0.4mm |
| Spray Holes Distribution | IPX3:over an arc of 60° either side of the center point (120°) IPX4:over the whole 180° of the semicircle Hole spacing: 50mm |
| IPX3/4 Switching | Switching by changing a certain number of blind hole needles or through-hole needles |
| Oscillating Angle | IPX3:120°(±60°)； IPX4:350°(±175°) |
| Oscillating Speed | IPX3:4s /cycle(2×120°); IPX4:12s /cycle(2×350°); |
| Oscillating Tube Position | Located in the middle of the inner chamber, the left and right ends are fixed on the side wall of the inner chamber |
| General | |
| Waterproof Turntable | Diameter:Φ400mm,rotation speed: 1-5r/min, with 15° sample support block,and lifting frame 400-750mm adjustable, bearing capacity:≤50kgs |
| Control & Operation | PLC and touch screen intelligent control system |
| Test Duration | 0-99.9min, can be preset |
| Chamber Material | Inner chamber is made of SUS304 stainless steel |
| Water Circulation System | The test is processed in the chamber, the equipment has a bilt-in water tank, the water can be recycled. And the inner chamber has a water collecting device, the test water is automatically collected into the water storage tank through the chassis. The water inlet can be automatically controlled through the float valve in the water tank, the system can give out high and low water level alarm detection alarms, which can effectively prevent the pump from being damaged due to dry water shortage. Also, there is a cleaning filter device at the water inlet position. |
| Safety Protection | Phase sequence protection, leakage protection, water shortage protection, abnormal protection |
Use place: temperature 15-35 ° C, relative humidity 25%-75%, atmospheric pressure 86 ~ 106kpa (860 mbar -1060 mbar), there should be equipped with lighting and waterproof leakage switch (or socket), the ground needs to be flat, and the water intake and drainage function should be good.
Water source: clean water or tap water without impurities, equipped with water cleaning filter.
