Shenzhen Sunbow Insulation Materials MFG. CO., LTD |
|
Black Polyolefin Heat Shrink End Cap Cable Accessories
The End Cap is adhesive lined to bond with the heat shrink it
overlaps
Hot melt adhesive seals and insulates in one step to speed
installation
Adhesive lining will prevent moisture penetration, allowing for
long term storage of cable
Forms pressure-tight seal on ends of communication and power cables
Shrink ratio of 2:1 insulates a wide range of diameters and
irregular shapes
Cross-linked UV resistant material improves chemical and
temperature resistance
Continuous use temperature of up to 105 °C
Shrink temperature of 110-130 °C
Dual wall end cap, with internal wall of hot-melt adhesive provides
excellent bonding to plastic and metals.
Capable of sealing the entire surface of a cable or wire
Specification
Property | Test Method | Standard Value |
Operating temperature | IEC 216 | -45ºC to+105ºC |
Tensile strength | ASTM-D 2671 | ≥13MPa |
Elongation at break | ASTM-D 2671 | ≥300% |
Tensile strength after aging | ASTM-D-2671/120ºC,168hrs | ≥10MPa |
Elongation at break after aging | ASTM-D-2671/120ºC,168hrs | ≥240% |
Dielectric strength | IEC 243 | ≥15kV/mm |
Volume resistance | ASTM-D-2303 | ≥1×1013Ω.cm |
Dielectric constant | IEC 250 | 3.0 |
Radial shrinkage | - | ≥50% |
Eccentricity | ASTM-D-2671 | ≤35% |
Low Temperature Flexibility | ASTM-D-2671 | -40ºC, 4hrs, no cracking |
Minimum shrink temperature | - | 90ºC |
Minimum fully recovered temperature | - | 130ºC |
Dimension
Size | Size after recovery(mm) | Size as supplied (mm) | Cable sizes(mm) | |||
Size | Inner Diameter | Wall thickness | Inner Diameter | Wall thickness | length | Outer Diameter |
Φ 11 | ≤6.5 | 1.1±0.1 | ≥11 | 0.7±0.2 | ≥22 | Φ6-9 |
Φ 16 | ≤8.0 | 2.5±0.1 | ≥16 | 1.2±0.2 | ≥70 | Φ9-14 |
Φ 20 | ≤8.0 | 2.5±0.1 | ≥20 | 1.2±0.2 | ≥70 | Φ9-17 |
Φ 25 | ≤11 | 2.5±0.1 | ≥25 | 1.2±0.2 | ≥80 | Φ12-22 |
Φ 32 | ≤17 | 2.6±0.1 | ≥32 | 1.5±0.2 | ≥90 | Φ17-27 |
Φ 40 | ≤15 | 2.8±0.1 | ≥40 | 1.5±0.2 | ≥90 | Φ20-35 |
Φ 55 | ≤25 | 2.8±0.1 | ≥55 | 1.5±0.2 | ≥125 | Φ28-45 |
Φ 75 | ≤30 | 3.2±0.1 | ≥75 | 1.8±0.2 | ≥145 | Φ40-65 |
Φ 100 | ≤42 | 3.5±0.1 | ≥100 | 1.8±0.2 | ≥140 | Φ50-90 |
Φ 120 | ≤59 | 3.5±0.1 | ≥120 | 1.8±0.2 | ≥155 | Φ70-110 |
Φ 140 | ≤63 | 4.0±0.1 | ≥140 | 2.0±0.2 | ≥180 | Φ90-130 |
Φ 250 | ≤94 | 4.0±0.1 | ≥250 | 2.0±0.2 | ≥270 | Φ120-240 |