|
[China]
Trade Verify
Address: Room 101-301, No. 36, Xingda Road, Yanchuan Community, Yanluo Street, Shenzhen, Guangdong, China
Contact name:Li
Shenzhen Senring Electronics Co., Ltd. |
|
Verified Suppliers
|
|
|
Customized Hollow Shaft Size Electrical Rotary Union Support 6~8mm Pipes
Description of 3502006 Hollow Shaft Slip Ring
The SenRing 3502006 series pneumatic rotary joint is a dual-channel rotary joint that can rotate 360 degrees to transmit two channels of compressed air, steam, vacuum, and other gas media. It is suitable for 6mm and 8mm air pipes. In addition, this 3502 series rotary pneumatic joint can not only transmit gas but also mix and transmit various electric currents ranging from 2A to 800A. This rotary joint is characterized by its small size, light weight, low torque, and multiple gas passages that do not interfere with each other.
Technical Specification of 3502006 Hollow Shaft Slip Ring
| Passages(Gas) | 2 passages |
| Pipe Size | 6~8mm pipe, G1/8"; Port |
| Mechanical Data | |
| spec. | data |
| Working life | 20millions for ref(depends on working conditions) |
| Max. Operating Speed | 250RPM continously, 1000RPM intermittently |
| Working temp. | -30°C~80°C |
| Work humidity | 0~85% RH |
| Contact Materia | Precious Metal |
| Housing Material | aluminum alloy |
| IP Grade | IP51 |
| Max. Operating Pressure | Positive Pressure 1Mpa, Vacuum -90kPa | |
| torque | <0.2N.m | |
| Electrical Data | ||
| spec. | data | |
| Power | Signal | |
| Voltage range | 0~440VAC/VDC | 0~440VAC/VDC |
| Insolution resistance | <500MΩ/300VDC | <500MΩ/300VDC |
| Lead wire spec. | AWG17# Silver-plated teflon wire | AWG22# Silver-plated teflon wire |
| Lead wire length | standard 250mm (can be customized) | |
| Insolution resistance | 500VAC@50Hz,6s | |
| Electrical noise | <0.01Ω | |
A hollow 50mm pneumatic rotary joint is a device that allows compressed air or other gases to be transferred between a stationary component and a rotating component in a pneumatic or hydraulic system. It features a hollow center that allows for a rotating shaft to pass through the center of the joint while the gas or fluid is transferred through the joint.
The rotary joint consists of two parts, a stationary part and a rotating part, which are connected by a set of seals that prevent gas or fluid leakage. The stationary part is mounted to the fixed component of the system, while the rotating part is mounted to the rotating component. The rotary joint is designed to handle a maximum pressure and flow rate of the gas or fluid being transferred.
Features of 3502006 Hollow Shaft Slip Ring
1. Max. Pressure(s):1Mpa (vacuum: -100kPa, higher Pressure can be customized)；
2. Support 2 G1/8" port for 6~8mm pipes;
3. Standard hollow shaft size 50mm.
4. Can be installed with mechanical arm to rotate together ;
5. Support transmitting mixed power and signals, such as USB, HDMI, 1000M ethernet, VGA, DVI, coaxial RF (high frequency), servo motor signal, industrial bus slip rings...etc;
6. 360° transmits compressed air, steam, vacuum, negative pressure, positive pressure...etc;
Part no. description
Drawing
Standard model list
| Model | Passages(Gas) | Port Size | Pipe Size |
| 3502006 | 2 passages | G1/8" | 6∼8mm |
| Model | Passages(Gas) | Port Size | Pipe Size | Power Circuits(10A) | Signal Circuits(5A) | Length L(mm) |
| 3502006-1205 | 2 Passages | G1/8" | 6∼8mm | 0 | 12 | 74 |
| 3502006-1210 | 2 Passages | G1/8" | 6∼8mm | 12 | 0 | 74 |
| 3502006-1805 | 2 Passages | G1/8" | 6∼8mm | 0 | 18 | 100 |
| 3502006-1810 | 2 Passages | G1/8" | 6∼8mm | 18 | 0 | 100 |
| 3502006-2405 | 2 Passages | G1/8" | 6∼8mm | 0 | 24 | 124 |
| 3502006-2410 | 2 Passages | G1/8" | 6∼8mm | 24 | 0 | 124 |
