Home Companies Ain Technology (Shenzhen) Co., Ltd

ALEPH Durable Request To Exit Motion Detector With Wall Or Ceiling Mounted OD22;

Active Member

Contact Us

[China]

Address: No. 301A, 3F, C6 Bldg, Hengfeng,No 739 Zhoushi Rd,Hezhou, Hangcheng, Bao'an, Shenzhen City, 518000 China

Contact name:Spring_zhang

Ain Technology (Shenzhen) Co., Ltd

ALEPH Durable Request To Exit Motion Detector With Wall Or Ceiling Mounted OD22;

Country/Region	china
City & Province	shenzhen guangdong
Categories	Other Access Control Products

Product Details

ALEPH OD22: REQUEST-TO-EXIT Passive Infrared Sensor

1. SPECIFICATIONS

Supply Voltage			12-24VDC or VAC .
Supply Current			18-30mA@12-24VDC,45-80mA@12-24VAC
Relay Output			2C Contact(N.C/N.O) , 24VDC 1A Max.
Detection Type			Passive infrared
Relay Hold Time			0.5-64 seconds
LED Indication			Red
Range			Coverage 12x5 ft at 7ft high,30x12 ft at 15 ft high(Adjustment )
Operating Temperature			- 14°F to 131°F(- 10° C to 55°C)
Weight			0. 4lb( 0. 18kg)
Humidity			0-95% non-condensing
Dimensions			6.53"Wx1. 57"Hx1. 53"D( 166x40x39mm)

FEATURES FOR ALEPH OD22

• Adjustable second time delay

• High sensitivity

•Micro-based signal processing

2. DIMENSIONS

3. DETECTION PATTERN

4. INSTALLATION

Mounting Procedure

1. Select a mounting location over the center of the door or doors to be covered. Mount the detector on the ceiling wall or door frame.

2. Remove the front cover from the detector.

3. Loosely mount the back cover to the mounting surface using the supplied mounting screws.

4. Aim the detector for the desired coverage.

. Mount the front cover on the detector.

Long Range/Short Range Adjustment

The OD-22 can be set to detect individuals at either a long rang(several steps from the door) or at short range (immediately in front of the door).If the build- ing includes a lengthy approach to the exit doorway and no other foot traffic in the area, choose the long range setting.

Setup and Testing

1. Apply power to the unit.

2. Wait at least 3 min for the detector to settle.

3. Test the unit by walking directly through the coverage area toward the door.

4. Aim the detector up or down if necessary to obtain the proper coverage.

5. Check that the relay latch time is sufficient to adjust if necessary.

6. After confirming proper operation, replace the cover and walk test one more time to ensure the coverage has not changed.

6. WIRING

Latch Time

DIP Switch 1,2, and 3 set the relay time. Latch time is adjustable from 0.5 sec to 64 sec. It indicates the amount of time the relay can remain active after the detector first sees motion.

Table1: Latch Time DIP Switch Settings
Time(sec)	Switch 1	Switch 2	Switch 3
0.5(Default)	OFF	OFF	OFF
1	ON	OFF	OFF
2	OFF	ON	OFF
4	ON	ON	OFF
8	OFF	OFF	ON
16	ON	OFF	ON
32	OFF	ON	ON
64	ON	ON	ON

Table 2: LED Enable/Disable DIP Switch Settings
Switch 4			Function
OFF			Disabled
ON			Enabled (Default)

Table 3:Relay Mode DIP Switch Settings
Switch 5			Function
OFF			Fail Secure
ON			Fail safe(Default)

Table 4:Resettable/Non-resettable DIP Switch Settings
Switch 6			Function
OFF			Non-resettable
ON			Resettable (Default)

7. TROUBLE SHOOTING AND MAINTENANCE

TROUBLE	TROUBLE CAUSE	REMEDY
the unit does not power up	No or low input power.	Apply proper input voltage.
	Input power polarity reversed.	Correct wiring polarity.
Alarm LED does not light	the LED jumper is set to “LED OFF”.	Set LED jumper to “LED ENABLE”
	Incorrect sensor mounting height	Increase /decrease mounting height
LED indicates light,no signal output	Incorrect wiring at output terminals	Correct wiring fault.
	Lightning damage	Replace sensor.
Unit continues to operate after the input power has been disconnected.	The wire to the “V-” power input was discon- nected, the “V+” is still connected.	Disconnect wire from the “V+” power input.

MAINTENANCE

INSPECTION: An inspection of this unit should be made periodically, consisting of but not limited to all mounting, wiring

and the condition of the interior area and components.

CLEANING: Clean the plastic parts of this unit with a soft, clean, cloth dampened with water.

TESTING: This unit should be tested routinely for proper operation. At a minimum,operation should be fully checked yearly.

Hot Products

Curtain Passive Infrared Detector With Direction Identification BLC-20

Contact Us

Ain Technology (Shenzhen) Co., Ltd

ALEPH Durable Request To Exit Motion Detector With Wall Or Ceiling Mounted OD22;

Product Details

Hot Products

Curtain Passive Infrared Detector With Direction Identification BLC-20

Easy Installation Mini Pir Motion Sensor , Curtain Motion Detector

Dual Element Passive Infrared Detector High Performance CE ISO Approved

Strong Stability Pir Based Motion Detector High Density Detection Area

10-16V DC Curtain Passive Infrared Detector With -10℃-55℃ Operating Temperature

Ceiling Mounted Pir Motion Detector 10-16VDC With Anti Masking Function