Beijing Real Healthcare Medical Equipment Co., Ltd |
Verified Suppliers
|
|
Multiple Functions Anesthesia Machine Suitable For Pediatric And Adults
Features
1. Suitable for pediatric and adults;
2. Tidal volume setting 50-1500mL;
3. Friendly user interface;
4. 8" LCD color screen with touch screen;
5. Knob and hard key input.
6. Sufficient modes ventilation: VCV, PCV, SIMV-V, Manual;
Environmental Specifications | ||||
Work Environment | Storage Environment | |||
Temperature | 10~40 ℃ | Temperature | -20~55 ℃ | |
Humidity | 5~95%,non-condensing | Humidity | 10 ~ 95%, non-condensing | |
Barometric pressures | 70~106 KPa | Barometric pressures | 50~106 KPa |
Gas Supplies | |
Pipeline gases | O2, Air, N2O |
Cylinder gases | O2, N2O (3 cylinders maximum) |
Cylinder connections | Pin indexed |
Primary regulator output pressure | Less than 400kPa |
Pipeline connections(filtered) | DISS, NIST. All fittings available for O2, Air and N2O |
Pressure displays | Pressure gauges |
Pipeline inlet pressure | 280-600 kPa (41-87) psi |
Flush flow | 25L/min to 75L/min |
N2O Cut-off pressure | Internal O2 supply pressure less than 90 kPa |
ACGO | |
Connector | Male 22 mm conical connector incorporating a coaxial female 15mm conical connector. Shared with inspiratory port. |
Fresh gas | |
6 tubes flowmeter | Air range: 0 to 15 L/min O2 range: 0 to 10 L/min N2O range: 0 to 12 L/min Accuracy: < ±10% of the indicated value (under 20 ℃and 101.3 kPa, for flow between 10% of full scale or 300mL/min (whichever is greater) and full scale) |
O2-NO2 link system | Mechanical device for hypoxic guard, O2 concentration not lower than 25% |
Auxiliary O2 supply | |
Gas supply | O2 in the system |
Flow range | 0 to 15 L/min |
Accuracy | ±10% of reading value or ± 200 ml/min, whichever is greater(under 20℃and 101.3 kPa) |
External AC power | ||
Input Voltage | 100-240V | |
Input Frequency | 50/60Hz | |
Input Power | <150 VA | |
System leakage current limit-do not exceed | Less than 500 uamps for the system and all systems connected to electrical outlets. | |
Resistance to ground | Less than 0.2Ω | |
Fuse | T10AL/250V | |
Power cord | 5 M | |
Auxiliary output supply | ||
Output voltage | 220-240V | 100-120V |
Output frequency | 50/60Hz | 50/60Hz |
Internal Battery | ||
Number of batteries | one battery | |
Battery Type | NiMH | |
Rated battery voltage | 12VDC | |
Battery capacity | 4200mAh | |
Shutdown Delay | Less than 10min (powered by new fully-charged battery after the first low-power alarm) | |
Shortest supply time | 90min | |
Charging time | 4h |
Machine | |||
Size | 1410× 950 × 650 (H × W × D) | ||
Weight | Approximately110kg | ||
Maximum bearing weight of the top cover | 30kg | ||
Display | |||
Type | Color TFTLCD (touch screen) | ||
Size | 8.4 inches | ||
Resolution | 640 × 480 pixels | ||
Brightness | Fixed | ||
Audio instruction | |||
Speaker | Alarm sounds, tone: supports multi-level volume, alarm tone meet IEC60601-1-8 standards. | ||
Control | |||
Knobs | Support clockwise/ counterclockwise rotation and pressing operation | ||
Button | Alarm pause, alarm reset, standby, back to the main screen | ||
Interface | |||
Power supply | An AC power inlet Three auxiliary output outlets | ||
Monitor | A standard color VGA monitor connector ,15-PIN D-sub socket | ||
Equipotential | An equipotential ground terminal | ||
USB | Standard USB connector | ||
Moving means | |||
Roller | 4 castors, diameter 125mm | ||
Brake | |||
Brake plate | Brakes for four casters | ||
Toolbox | |||
Drawer | Drawer:200 × 392 × 398 (H × W × D) Drawer two:200 × 392 × 398 (H × W × D) | ||
Breathing System Specifications | |||
Bellow Volume | About 1500mL | ||
Absorber canister volume | About1500mL | ||
Connector | ACGO ports: standard OD 22mm, ID 15mm, tapered connector; Inhalation and exhalation ports: standard OD22mm, ID 15mm, tapered connector Manual bag port: standard OD22mm, ID 15mm, tapered connector | ||
System Leaks | In any mode, the system is not greaterthan140ml/min leakage | ||
System Compliance | Volume of gas lost due to internal compliance (Manual mode only):<3.0 ml/0.098 kPa (1 cmH2O) <120 ml/3 kPa (30 cmH2O) | ||
APL Valve | Approximately 0 to 70 cmH2O | ||
Airway Pressure Gauge | -20 to +100 cmH2O | ||
Water Collection Cup | Can be disassembled independently. Approximately 12mL. | ||
Alarm Settings | |||
Tidal Volume | High: 30 ~ 2000 mL, OFF Low: 20 ~ 1500 mL | ||
Minute Volume | High: 1 ~ 99 L Low: 0 ~ 98 L | ||
Respiratory Rate | High: 1 ~ 100bpm Low: 0 ~ 99 bpm | ||
FiO2 (optional) | High: 19 ~ 100%, OFF Low: 18 ~ 99% | ||
Airway Pressure | High: 10 ~ 99 cmH2O Low: 1 ~ 98 cmH2O | ||
ETCO2 (optiona) | High: 0.1 to 13.3%; Low: 0 to 13.2% | ||
Pulse (optional) | High: 31~250 bpm Low: 30~249 bpm | ||
SpO2 (optional) | High: 50~99%,OFF Low: 49~99% | ||
Continuous Pressure High | Airway pressure greater than (PEEP +15) cmH2O, 15 sustained when an alarm is triggered. | ||
Negative Pressure Alarm | Airway pressure is less than (-10) cmH2O. | ||
Apnea Alarm | Setting time is 10 ~ 60s, in increments of 1s. | ||
Oxygen Deficiency Alarm | Oxygen pressure is less than 280 kPa. | ||
AC Power Failure Alarm | The mains break down or the power cord disconnects | ||
Low Battery Alarm | More than 10 minutes | ||
Alarm battery is exhausted | More than 5 minutes | ||
Silent Alarm | ≤ 120 s | ||
Anesthetic Vaporizer(optional) | |||
Vaporizer position | Double vaporizer positions | ||
Mounting mode | With interlocking function | ||
Applicable standard | ISO80601-2-13 | ||
AGSS Transfer and Receiving System | |||
Type of disposal system | Low-flow disposal system | ||
Applicable standard | ISO80601-2-13 | ||
Pump rate | 25 to 50 L/min | ||
Pressure relief device | Pressure compensation opening to the air | ||
Filter | Stainless steel filter,140 ~ 150μm | ||
State indication of the disposal system | The float falls below the “MIN” mark on the sight glass when the disposal system does not work or the pump rate is lower than 25L/min. |
Company Profile
As a premier healthcare devices supplier of Anesthesia Machine, RHC strives to provide better care for more people around the globe.
Our focus is to be a single supplier for all of your major Operating Room and ICU equipments. Our clients find that with one point of contact, the purchasing process is a much more efficient and pleasant process.
The offered range of Anesthesia Machine is manufactured using high quality components that are sourced from certified and trustworthy vendors of the industory. These products are highly demanded in the market owing to their remarkable features and affordable prices. Furthermore, we ensure to timely deliver these products of Anesthesia Machine to our clients, through this, we have gained a huge clients of volumetric infusion pump base in the market.
FAQ
1. What is time of delivery?
Since our products of Anesthesia Machine are produced according to each specific order, the delivery period will be 3-7 working days after confirmation of order. If it is small or sample order, please do check with us about whether we have ready goods in stock to make delivery as soon as possible.
2. What about quality assurance?
We offer 1 year warranty period beginning from the time of shipment for medical equipment of Anesthesia Machine, Per minor problems, we can provide free spare parts for replacements, Per serious problems, we can make replacement of free charge. But if the machine of Anesthesia Machine is damaged due to rough handling during the transportation, we are free of any responsibility, but we will still provide help to the buyer issue claims against the shipping company or insurance company, thus all the spare parts or expense of Anesthesia Machine should be borne by buyer.
3. What about the price level?
We are confident that our prices of Anesthesia Machine are competitive compared with those at the same quality level, since we have stayed in this field about 8 years. And we always adhere to the principle of provide top quality products with competitive prices. We have already established our good fame in many countries, especially in Africa, Middle East, European, Asia and South America through year after year efforts.
4. Why we find some prices are very high compared with some other supplier, and from the picture or it's model number all looks the same?
As China is still a developing country, there are only a few products of Anesthesia Machine with patent rights,and copy products are spread very fast in the market. Of course, the prices of those copy Anesthesia Machine with cheap material and less quality control are relatively cheaper.
5. What is payment terms?
T/T in advance.
6. Which shipping company usually using?
MAERSK-LINE, PIL, COSCO, SAFMARINE, MARUBA, APL, CMA, CSAV, K-LINE, MSC, NYK, AND DHL, EMS, TNT, UPS FOR COURIER, buyer's option will be our priority, we will give suggestion according to the schedule and services.