Home Companies Changzhou TIANNIU Transmission Equipment Co., Ltd

Deep Groove Clutch CKZ-A Series One Way Ball Bearing Sprag Type Freewheels Two Set

Contact Us

[China]

Trade Verify

Address: No. 203, Gaotiantou, Liudao Industrial Park, Yaoguan Town, Wujin District, Changzhou City, Jiangsu Province

Contact name:Christina Liu

Changzhou TIANNIU Transmission Equipment Co., Ltd

Verified Suppliers

Trust
Seal
Verified
Supplier
Credit
Check
Capability
Assessment

Deep Groove Clutch CKZ-A Series One Way Ball Bearing Sprag Type Freewheels Two Set

Country/Region	china
City & Province	changzhou jiangsu

Product Details

Deep Groove Clutch CKZ-A Series One Way Ball Bearing Sprag Type Freewheels Two Set

Production introduction

CK-A series is a wedge type one-way clutch without bearing support. Radial dimensions are the same as standard bearing dimensions. When used, it needs to be installed with the bearing to bear the axial load and radial load. Grease has been added at the factory.
The standard installation method is that the CK-A model is coaxially side-by-side with the bearing, and the same tolerance requirements are required. The inner and outer rings are keyed to the shaft and hub.
This series is commonly used in elevators, conveyors, packaging, printing, food, medical, textile, chemical and other mechanical equipment.

1. CKZ-A Series Cam Clutch is Shielded by shield bearings on both ends, packed with a special grease, and are ready for use. No additional lubricant is required.
2. For attaching pulleys, gears or sprockets to the clutches, insert hubs (with f7 tolerance of ISOR773) along the inner surface of the outer race and screw the bolts (high tension) into the tapped holes on the clutch end.
3. Recommended shaft tolerances are shown in the table on the lower left.
4. External thrust load should be supported by other devices, not by the Cam Clutch.
5. Use only a parallel key to secure the clutch to the shaft. Do not use a tapered Key.
6. When mounting the clutch onto the shaft, apply pressure to the inner race but never to the outer race.
7. Ambient temperature range is 5° To 40° C.
8. Key to be used should be in accordance with ISOR773. (DIN 6885.1)

Products Parameters

Type	Torque Nm	Overrunning Speed r/min		Size								Weight kg
				mm
		Inner Race	Outer Race	Dh7	B	F	n-M	H	D H7	C	bn×tn
CKZ-A2080	175	1200	510	80	60	68	4-M6	15	20	62	6×2.8	1.89
CKZ-A35100	630	1000	425	100	78	86	6-M8	20	35	80	10×3.3	3.60
CKZ-A40115	1115	900	400	115	80	100	6-M8	20	40	82	10×3.3	4.89
CKZ-A40120	1160	900	400	120	80	105	6-M8	20	40	82	10×3.3	5.39
CKZ-A42125	1268	900	400	125	90	105	6-M8	20	42	92	12×3.3	6.56
CKZ-A45140	1585	750	350	140	95	120	6-M10	25	45	97	14×3.8	8.78
CKZ-A50150	1900	700	300	150	95	130	6-M10	25	50	97	14×3.8	9.99
CKZ-A55160	2290	600	250	160	105	140	6-M10	25	55	107	16×4.3	12.47
CKZ-A65170	2720	600	200	170	105	150	6-M10	25	65	107	16×4.3	13.63
CKZ-A70180	3100	500	150	180	110	160	6-M10	25	70	112	2×4.9	15.91
CKZ-A1890	400	1100	460	90	54	75	6-M6	15	18	56	6×2.8	2.46
CKZ-A2590	400	1100	460	90	49	75	6-M6	15	25	50	8×2.5	2.35
CKZ-A25100	630	1000	425	100	79	88	6-M8	16	25	80	8×3.3	4.12
CKZ-A28100	630	1000	425	100	78	86	6-M8	20	28	80	8×3.3	3.98
CKZ-A30100	630	1000	425	100	78	86	6-M8	20	30	80	10×3.3	3.80
CKZ-A32100	630	1000	425	100	78	86	6-M8	20	32	80	10×6.3	3.71
CKZ-A38115	1115	900	400	115	80	100	6-M8	20	38	82	10×3.3	4.90
CKZ-A45125	1268	900	400	125	90	110	8-M8	25	45	92	14×3.8	6.51
CKZ-A50135	970	800	400	135	70	115	6-M10	20	50	72	14×3.8	6.61
CKZ-A5138	1580	750	350	138	101	124	6-M8	20	45	105	12×5.0	8.85
CKZ-A50160	2290	600	250	160	90	140	6-M10	20	50	90	14×3.8	12.86
CKZ-A50180	3100	500	150	180	124	158	6-M10	25	50	128	14×3.8	16.9
CKZ-A55145	1850	700	300	145	100	130	6-M8	20	55	102	14×3.8	9.42
CKZ-A55170	2720	600	200	170	110	146	8-M8	15	55	112	16×4.3	14.23