Home Companies Fibre Easy Communication Service Limited

interface converter Network bridge of E1 to ethernet protocol converter

Fibre Easy Communication Service Limited
Active Member

Contact Us

[China] country

Contact name:Soda

Inquir Now

Fibre Easy Communication Service Limited

interface converter Network bridge of E1 to ethernet protocol converter

Country/Region china
InquireNow

Product Details

interface converter Network bridge of E1 to ethernet protocol converter

Product Overview

E1-4ETH interface converter is based on FPGA.The device provides the transition between ITU-T G.703 (E1) standard unframed E1 interface and 10/100Base-T interface. It is a high capability, self-adaptable long-distance Ethernet bridge.The product is small and with low cost. It is widely used in connecting between WAN and LAN, monitoring, etc

Features

  • Can realize monitor and control of remote equipment, OAM management data did not take up users’ timeslot and save E1 bandwidth
  • Have the function of E1 interface loop back check, avoid the converter crashed because of interface loop return;
  • Have indicator when the device is power-off or E1 line is broken or lose signal;
  • Can set the E1 line that not to send the LINK signal to Ethernet interface while E1 line is broken;
  • The Ethernet interface supports jumbo frames (1916 Bytes);
  • 4Channel 10M/100M Ethernet interface can isolate each other to realize communication independently;
  • Ethernet interface supports10M/100M, half/full duplex auto-Negotiation and AUTO-MDIX (crossed line and straightly connected line self-adaptable );
  • Provide 2 clock types: E1 master clock and E1 line clock;
  • Have three Loop Back Mode: E1 interface Loop Back (ANA),Ethernet interface Loop Back(DIG),Command the remote Ethernet interface Loop Back(REM)
  • Have pseudo random code test function, easy the installation and maintenance;
  • Provide 2 impedances: 75 Ohm unbalance and 120 Ohm balance;
  • Have Ethernet monitor self-reset function, the equipment will not dead
  • Ethernet interface supports the counters of receiving and transmitting frame, receives wrong frame counters. E1 interface supports the counters of receiving wrong frame;
  • Realize monitor of remote equipment temperature and voltage from local equipment;
  • Support SNMP Network Management;
  • Can form the structure: Ethernet E1 Bridge(A)---E1 Optical Fiber Modem(B)---Ethernet Optical Fiber Modem (C)

Technical parameters

 

E1 Interface

Interface Standard: comply with protocol G.703;
Interface Rate: 2048Kbps±50ppm;
Interface Code: HDB3;

E1 Impedance: 75Ω (unbalance), 120Ω (balance);

Jitter tolerance: In accord with protocol G.742 and G.823

Allowed Attenuation: 0~6dBm

Ethernet interface (10/100M)

Interface rate: 10/100 Mbps, half/full duplex auto-negotiation

 

Interface Standard:

 

Compatible with IEEE 802.3, IEEE 802.1Q (VLAN)

MAC Address Capability: 4096

Connector: RJ45, support Auto-MDIX

Power

Power supply: AC180V ~ 260V;DC –48V;DC +24V

Power consumption: ≤3W

Dimension & Weight

Product size: 216 X140 X31mm( WXDXH)

Simple packaging: 274 X193 X84mm(WXDXH)

Piece weight: 1.2KG

 

Working environment

Working temperature: -10°C ~ 50°C
Working Humidity: 5%~95 % (no condensation)

Storage temperature: -40°C ~ 80°C
Storage Humidity: 5%~95 % (no condensation)

Networking Application

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Hot Products

360 POTS telephone FXO FXS over fiber optical multiplexer with 4*100M / 1000M Ethernet Product ...
E1 PCM 4POTS over coaxial cable Product Overview This device provides one E1 interface,4Channel ...
E1 PCM MUX 4POTS telephone extenders Product Overview E1-4Voice+FE+2RS232 Multiplexerprovides one E1 ...
Product Overview: E1-4Voice+FE+2RS232 Multiplexerprovides one E1 interface,4Channel telephoneoutput...
Product Overview: E1-4Voice+FE+2RS232 Multiplexerprovides one E1 interface,4Channel telephoneoutput...
Product Overview: E1-4Voice Multiplexerprovides one E1 interface,4Channel telephoneoutput,2Channel ...