Active Member
|
[China]
Address: ROOM 2204, NO.98， TIANGAO ALLEY, SOUTH BUSINESS DISTRICT, YINZHOU, 315194, NINGBO, CHINA
Contact name:Roy Zhang
Ningbo Anyo Import & Export Co., Ltd. |
|
|
Standard series SMD surface mount aluminum electrilytic capacitor
Feature:
• Chip type higher capacitance in larger case size
• Designed for surface mounting on high density PC board
• Applicable to automatic insertion machine using carrier tape
• Complied to the RoHS directive.
Specifications:
| Operating temperature range | -40~+85℃ | ||||||||||||||
| Leakage current max. | WV≤100 I=0.01CV or 3μA whcihever is greater (after 2 minutes) | ||||||||||||||
| Capacitance tolerance | ±20% at 120Hz, 20℃ | ||||||||||||||
Dissipation factor max. | WV | 4 | 6.3 | 10 | 16 | 25 | 35 | 50 | 63 | 100 | 160 | 200 | 250 | 400 | 450 |
| tan | 0.35 | 0.28 | 0.20 | 0.16 | 0.13 | 0.12 | 0.09 | 0.12 | 0.12 | 0.20 | 0.20 | 0.20 | 0.25 | 0.25 | |
| Small size between two sizes in dimension table and over the 6.3*5.8(ΦD*L) | |||||||||||||||
| Low temperature characteristics(Impedance ratio at 120Hz) | WV | 4 | 6.3 | 10 | 16 | 25 | 35~100 | 160~250 | 400~450 | ||||||
| Z-25℃/Z+20℃ | 6 | 5 | 4 | 3 | 2 | 2 | 3 | 6 | |||||||
| Z-40℃/Z+20℃ | 12 | 10 | 8 | 6 | 4 | 3 | 6 | 10 | |||||||
Load life | Leakage current | Less than specified value | |||||||||||||
| Capacitance change | Within ±20% of initial value (Small size:±25%) | ||||||||||||||
| Tan | Less than 200% of the specified value | ||||||||||||||
| Shelf life (at 85℃) | After 1000 hours no load test, leakage current, capacitance and tan are same as load life value. | ||||||||||||||
| Resistance to soldering heat | The following specification shall be satisfied when the capacitors are restored to 20℃ after exposing them at 250℃ for 30 seconds. | ||||||||||||||
| Leakage current | Less than specified value | ||||||||||||||
| Capacitance change | Within ±10% of initial value | ||||||||||||||
| Tan | Less than specified value | ||||||||||||||
Recommended conditions for reflow soldering:
The chip aluminum electrolytic capacitor is subjected to soldering
by reflow method.
Temperature and time conditions of reflow soldering shall be set as
per each temperature profile. The following are recommended
conditions in the case of reflow soldering method for the chip
aluminum electrolytic capacitor.
• The capacitor shall not be subjected to either flow or dip
soldering method.
• Avoid soldering twice by reflow. The number of reflow time
for chip aluminum electrolytic capacitor shall be once basically.
If this type of capacitor has to be inevitably subjected to the
reflow twice, enough cooling time between the first and the second
reflow ( at least more than 30 minutes) shall be taken to avoid the
consecutive reflows by all means.
• The touch up work with a soldering iron is allowed after the
reflow soldering (temperature of soldering iron: MAX 400℃, time 5
sec.), provided that carefully attention shall be paid lest a
soldering iron should directly touch the capacitor body or its
resin bottom base.
Dimension: (mm)
| ΦD*L | W | A | B | C | E | R |
| 4*5.3 | 4.8 | 4.3 | 4.3 | 1.0 | 0.5~0.8 | |
| 5*5.3 | 5.8 | 5.3 | 5.3 | 1.4 | 0.5~0.8 | |
| 6.3*5.8 | 7.1 | 6.6 | 6.6 | 2.2 | 0.5~0.8 | |
| 6.3*7.7 | 2.4 | 6.6 | 6.6 | 2.2 | 0.5~0.8 | |
| 8*6.2 | 3.3 | 8.3 | 8.3 | 2.3 | 0.5~0.8 | |
| 8*10 | 2.9 | 8.3 | 8.3 | 3.1 | 0.8~1.1 | |
| 10*10 | 3.2 | 10.3 | 10.3 | 4.5 | 0.8~1.1 | |
| 12.5*13.5 | 4.6 | 12.8 | 12.8 | 4.5 | 1.1~1.4 | |
| 16*16.5 | 5.6 | 16.8 | 16.8 | 6.5 | 1.1~1.4 | |
| 16*21.5 | 5.6 | 16.8 | 16.8 | 6.5 | 1.1~1.4 | |
| 18*16.5 | 6.6 | 18.8 | 18.8 | 6.5 | 1.1~1.4 | |
| 18*21.5 | 6.6 | 18.8 | 18.8 | 6.5 | 1.1~1.4 |
