Home Companies Shanghai Printyoung International Industry Co.,Ltd

Semi Automatic Hard Leather Book Hard Cover Case Maker Machine PRY-C480

Contact Us

[China]

Trade Verify

Address: Room 27B, NO,58 New Jinqiao Road, Pudong, Shanghai, China 201206

Contact name:Caren

Shanghai Printyoung International Industry Co.,Ltd

Verified Suppliers

Trust
Seal
Verified
Supplier
Credit
Check
Capability
Assessment

Semi Automatic Hard Leather Book Hard Cover Case Maker Machine PRY-C480

Country/Region	china
City & Province	shanghai shanghai

Product Details

PRY-C480 Semi-Automatic Case-Maker

This machine is composed by three parts of a gluing,folding flattening and electrical cabinet

4.1 As shown in the main power switch is used to turn the machine power on or turn it off.
4.2 Gluing roller power switch is used to the gluing roller run and stop.The gluing roller speed is adjusted by the knob.(Caution:The speed adjustment knob can not leave on the 70% position for long tine.It will reduce the lift of speed controller if keep 70% position with a long time).
4.3 Glue tank temp.controller is for the glue temperature control.It will be set in 65~75℃ in general but it may be increased or reduced properly according to the glue melting point and the weather changing.
4.4 Heater start switch is for the glue tank heating control.
4.5 Folding roller run switch is for tuming folding roller on or off.
4.6 Suction switch is used to the suction control.
Notice:The button and switch on the panel except the main power switch are individually controlled,the relation section can be turn on or off individually and regardless of order.

5.1 There are two adjusting knob on the right and left sides.They are used to adjust the glue thickness that is gluing on the paper.The glue thickness is needed to adjust according to the product requirement.

5.2 The picture above is glue bucket.It includes two parts.One is for the glue and another is for the water.
5.3 The water tank valve shown in the picture above is for cleaning glue.The hot water from the tank can clean the machine.
5.4 The bucket valve is for open and closes the glue supply.
5.5 The heater shown in the picture is for heating water and then melt the glue in the bucket.Its power is 6KW.
5.6 The temperature detect sensor shown in the picture above is for detecting the water temperature in the tank and then control it.
5.7 Adding glue pot,the water by heating to melt glue pot.

5.8 The water filling inlet is to fill additional water into glue tank.
Note:It is important to check the water level in the water tank and make sure it has enough water there before run the machine.There are the heaters installed in glue bucket and glue tank.Otherwise,the heater may be easy to damage.

6.1 The vacuum generator is shown in the picture.It generates the vacuum for the suction.
6.2 There are two sensors installed in the front shown in the picture and inside.These two sensors control the flatten roller forward and reverse running when do the folding.They are needed cleaning often to avoid their reaction reduce or fail due to the dust.
6.3 The folding pull finger located between the folding rollers is for the folding function.
6.4 The air filter is located under the working table.Its working pressure is bigger than 0.6kg/c㎡.It needs to lubricate and also exhaust water everyday from it.Keep the air dry and long life the pneumatic parts.

Mode

Normal operation,each time into the hem, When put Flap,only every two long sides folded,

each time in front of it. out from behind.

Flatten work,put off every time,directly out from the When you first folded out from the front on both sides,

rear,only to flatten. the second fold,from behind a finished finished.

Technical Parameters

PRY-C480 Semi Automatic Case Maker
Model	PRY-C480
Power Supply	3 phases 380 V / 50 Hz
Mainframe Power	6.5 KW
Work Speed	3-9 pcs/minute
Case Size(Maximum)	760 × 450 mm
Case Size(Minimum)	140 × 140 mm
Machine Dimensions	1600 × 1750 × 1600 mm
Paper Thickness	80-175 g
Machine Weight	650 kg

Product Requirements

When the paper thickness is less than 157gsm,the A area need to keep around 15mm,if the paper thickness is more than 157gsm, the A area need to correspond to big,if the paper thickness is more than 200gsm,the A area can not be less than 20mm.otherwise,the edge can not be folded.

Configuration

Gluing Part:There are two adjusting knob on the right and left sides.They are used to adjust the glue thickness that is gluing on the paper.The glue thickness is needed to adjust according to the product requirement.

There are two sensors installed in the front shown in the picture and inside.These two sensors control the flatten roller forward and reverse running when do the folding.They are needed cleaning often to avoid their reaction reduce or fail due to the dust.

The vacuum generator is shown in the picture.It generates the vacuum for the suction.

The folding pull finger located between the folding rollers is for the folding function.

Electrical cabinet.

Applications

This machine is the most applicable to various notebook,(photo album),folder, certificate, hardcover book,shell for folding(covering)and pressing,twice finished on both sides,one operator,forthright,Covers an area of small space,is post-press especially digital post-press good partner.

Q1.Are you a manufacturer or a trading company?

A:Our shanghai office is mainly doing export.We have our own factory in Wenzhou,Zhejiang Province.

Q2.What is the machine warranty?

A:One year.After the warranty,we still provide technical support to buyer at low cost.

Q3.What is the production time while placing order?

A:Normally about 10-20 days.

Q4.What is the delivery time?

A:15-30days after deposit.

Q5.Can your company handle shipping for customers?

A:Yes,just give us destination sea port or container yard.

Q6.Does the packing strong?

A:Yes.Adopts moisture-proof and shock-proof packaging which is suitable for long-distance road transportation and various types of weather conditions.A full set of maintenance and operation manuals is included.

Q7.How about the machine installation and training?

A:1)We provide training in our factory for free; 2)We can send technicians (engineers) to your factory for installation and training.You shall pay the round trip air fare and accommodations,plus each technician charges USD100/per day.

Q8.Do you have machines in stock?

A:For standard model,we have a large quantity in stock.For special model,we need 20-30 days to produce it for you.

Q9.How can you assure the machines’ quality?

A:Each machine will be test running at least 24 hours before delivery to assure the quality.

And during the warranty,we will give spare parts for free if machine has any problem.

Q10.Do you inspect machines or test running before packing?

A:Of course we do.We have QC department to debug the machine before packing.

If you want to use specific material to do the test running,you need to pay for the cost of the material.

Q11.What’s the payment term?

A:T/T 30% in advance,the balance shall be paid before delivery.We also accept payment by West Union or L/C at sight.

Q12.Do you accept factory visiting?

A:Warmly welcome for your visiting.

Q13.How many years are you in printing field?

A:The Shanghai company since in 2008,the factory is more than 25years.

Q14.How many clients do you have?

A:We have sold our machines to about 60 countries.We have agents in South Africa,Morocco and Italy.

Hot Products

PRY-JD260 V Shape Sharp Bottom Food Paper Bag Making Forming Machine 380V

Contact Us

Shanghai Printyoung International Industry Co.,Ltd

Semi Automatic Hard Leather Book Hard Cover Case Maker Machine PRY-C480

Product Details

Hot Products

PRY-JD260 V Shape Sharp Bottom Food Paper Bag Making Forming Machine 380V

PRY-JD350 V Shape Sharp Bottom Paper Bag Making Forming Machine For Snack Food Dry Fruit

Automatic Kraft Bubble Bag Poly Mailer Envelope Making Machine Two Side Seal

CFD60-4E/5E Automatic Elliptic Perfect Book Binding Machine Hot Melt Glue Binder

Semi Automatic Electric Twin Loop Wire Book Binding Machine PRY-520A

PRY-520PB Automatic Double Loop Wire Punching And Binding Machine Electricity Power