|
[China]
Trade Verify
Address: Liudao Industrial Pak, Yaoguan Town, Wujin District, Changzhou city, Jiangsu Province, 213102
Contact name:Ellen Zhang
Changzhou Suma Precision Machinery Co., Ltd |
|
Verified Suppliers
|
|
|
BS160 BS200 BS220 Holdback Backstop Clutch One Way Cam Clutch Bearings
Features
The BS series Cam Clutches are intended for applications where reverse rotation of the slow speed conveyor head shaft is to be prevented (backstopping).
1. For prevention of rotation in the reverse direction at slow
speeds on conveyors or pumps.
2. Before installation, verify that the direction of rotation of
the inner race of the BS Cam Clutch (shown by the arrow on the
inner
race) is the same as the direction of rotation of the conveyor.
3. Securely install the torque arm to the BS Cam Clutch using bolts
of strength 10.9 or higher. Make sure that the contact between
the surface of the torque arm and the side of the outer race is level and free of dust.
Dimensions and Capacities
Model | Torque Capacity (Nm) | Max. Overrunning (r/min) Inner Race | Drag Torque (Nm) | A | B | C | PCD D | E | S | H-M Size× Pitch × No.of Tapped Holes |
(kg) |
| BS30 | 294 | 350 | 0.58 | 64 | 90 | 64 | 80 | 45 | 13 | M 6 ×P1.0×4 | 2.1 |
| BS50 | 784 | 300 | 0.98 | 67 | 125 | 67 | 110 | 70 | 16 | M 8 ×P1.25×4 | 4.0 |
| BS65 | 1570 | 340 | 3.92 | 90 | 160 | 85 | 140 | 90 | 20 | M10 ×P1.5×6 | 11.5 |
| BS75 | 2450 | 300 | 5.88 | 90 | 170 | 85 | 150 | 100 | 20 | M10 ×P1.5×6 | 13.1 |
| BS85 | 5880 | 300 | 7.84 | 115 | 210 | 110 | 185 | 115 | 30 | M12 ×P1.75×6 | 24.7 |
| BS95 | 7840 | 250 | 9.8 | 115 | 230 | 110 | 200 | 130 | 30 | M14 ×P2.0× 6 | 29.4 |
| BS110 | 10800 | 250 | 14.7 | 115 | 270 | 110 | 220 | 150 | 30 | M16 ×P2.0× 6 | 34.2 |
| BS135 | 15700 | 200 | 19.6 | 135 | 320 | 130 | 280 | 180 | 30 | M16 ×P2.0× 8 | 68 |
| Type | Torque Capacity (Nm) | Max. Overrunning (r/min) Inner race | Drag Torque (Nm) | A | B | C | PCD D | E | S | H-M T.H.S.XP-Q'ty | G.F.H. (Size) | Q. of G. (kg) |
| BS 160 | 24,500 | 100 | 34.3 | 135 | 360 | 130 | 315 | 220 | 40 | M20xP2.5-10 | PT 1/4 | 0.12 |
| BS 200 | 37,200 | 100 | 44.1 | 150 | 430 | 145 | 380 | 265 | 40 | M22xP2.5- 8 | PT 1/4 | 0.14 |
| BS 220 | 49,000 | 80 | 73.5 | 235 | 500 | 230 | 420 | 290 | 40 | M20xP2.5-16 | PT 1/4 | 0.8 |
| BS 250 | 88,200 | 50 | 93.1 | 295 | 600 | 290 | 530 | 330 | 50 | M24xP3.0-16 | PT 1/4 | 1.1 |
| BS 270 | 123,000 | 50 | 98 | 295 | 650 | 290 | 575 | 370 | 50 | M24xP3.0-16 | PT 1/4 | 1.2 |
| BS300 | 176,000 | 50 | 108 | 295 | 780 | 290 | 690 | 470 | 60 | M30xP3.5-16 | PT 1/4 | 1.3 |
| BS335 | 265,000 | 50 | 137 | 305 | 850 | 320 | 750 | 495 | 70 | M36xP4.0-16 | PT 1/4 | 1.4 |
| BS350 | 314,000 | 50 | 157 | 320 | 930 | 360 | 815 | 535 | 70 | M36xP4.0-16 | PT 1/4 | 1.5 |
| BS425 | 510,000 | 50 | 216 | 440 | 1,030 | 450 | 940 | 635 | 70 | M36xP4.0-18 | — | Oil 6,000ml |
| BS450 | 686,000 | 50 | 245 | 450 | 1,090 | 480 | 990 | 645 | 80 | M42xP4.5-18 | — | Oil 7,000ml |
4. Recommended shaft tolerance is h7 or h8.
5. When inserting the BS Cam Clutch on the shaft, apply pressure
only on the inner race. Do not tap the inner race directly with a
hammer or exert any force upon the outer race, dust seal, or dust
plate.
6. Always use a parallel key for installation onto the shaft and
then fix the BS Cam Clutch to the shaft with the end plate. Never
use
a tapered key.
7. When installing models above BS160 (grease lubricated types),
place one of the four oil plugs in
The direct bottom location. This will allow for easy drainage of
the grease for cleaning.
8. While the shaft is rotating, the end of the torque arm will
swing to some extent in the direction of rotation. Support the
torque arm
end only in the direction of rotation, but be sure to allow it a certain amount of free swing. If the torque arm end is fixed securely
(see installation diagram), the inside of the clutch becomes
twisted, and this can result in damage to the components.
9. For models BS30 to BS200, a single torque arm on one side is
sufficient, but for models 220 to BS450, use two torque arms, one
on each side. Install the torque arms evenly so the force is
transmitted through the center of the clutch.
10. Torque arms for the BS Cam Clutch are standardized.
Pictures
