Suzhou Xunshi New Material Co., Ltd |
Verified Suppliers
|
|
NI-SPAN-C alloy 902(N09902) is a Fe-Ni Alloy with controllable thermoelastic coefficient. The desired thermoelastic coefficient is then obtained by using cold work and the proper thermal treatment. Cold work produces internal strains, making the coefficient more negative. Thermal treatments, in the lower temperature ranges, relieve strain. They also cause complex ordering phenomena which make the coefficient more positive. Heating at temperatures above about 900°F causes the precipitation of an intermetallic compound of titanium and nickel, withdrawing nickel from the matrix and moving the coefficient further in the positive direction.
Thermoelastic Coefficient
The thermoelastic coefficient (TEC) of an alloy is the rate
of change of its modulus of elasticity with change
in temperature. It is usually expressed as parts per million
per degree F (e.g. 5 x 10-6/°F).
The first measurements of the TEC of NI-SPAN-C alloy 902 were
made using a torsion pendulum operating at about one cycle per
second. These tests are the basis for much of the published
data on the alloy. However, when these data were used to
design high frequency devices they were found to produce
incorrect results, and a confused situation arose.
Recent work has solved the problem of the conflicting results.
It has been found that operating frequency has a marked effect
on TEC. Tests run at Special Metals showed that the TEC of a
given sample increased with increase in test frequency up to
about 800 cps. Above 800 cps there was no frequency effect.
Samples from the same heat of materialtested at about 1500 cps, and
in another laboratory at
455,000 cps, gave identical results. Burnette at the
National Bureau of Standards found that a heat treatment
which produced zero TEC on a sample tested in a torsion
pendulum at 1 cps developed a TEC of +40 on a sample tested in
freefree vibration at 1000 cps. Figure 2 shows these data and
a schematic indication of the frequency effect.
Because of the frequency effect, it is necessary to delineate
two areas of application of NI-SPAN-C alloy 902, each
requiring different processing to achieve best results.
These are:
1. Low frequency devices. These include springs, Bourdon
tubes, aneroid capsules, etc.
2. High frequency devices. Tuning forks, vibrating reeds,
mechanical filters and similar instrumentation fall in this
category.
Physical properties
Density: 8.05 g/cm3
Curie Temperature: 190°C
Electrical Resistivity: 1.02 µΩ•m
Cold work causes an increase in the modulus. Raising the temperature of heat treatment also causes an increase.
Although the alloy was designed for use above -50°F, it has
been used successfully at lower temperatures and some
cryogenic data have been
published. The alloy exhibits low damping capacity (high
Q). The Q of cold worked material has been reported to
be about 8000, about 4 times greater than the values
for annealed forms.
About XUNSHI
Suzhou Xunshi New Material Co. Ltd- referred as XUNSHI hereafter, is a professional manufacturer of high-performance alloy products. XUNSHI is engaged in supplying high quality and cost-effective Superalloy, Anti-Corrosion Alloy, Precision Alloy, Special Stainless Steel and Magnetostrictive Material to customers worldwide.
Why XUNSHI
· Highly experienced in alloy industry
· Top experts of industry in China
· Advanced technology and process from top famous institutes in China
· Advanced devices through whole production and inspection process
· Strict quality control system
· Company motto: best service, most value
· Smart sales policy
Service Items of XUNSHI
· Non-standard product research and pre-production
· Fabrication of products
· Cutting, splitting for sheets and plates in stock
· Heat treatment (Solution treatment, aging harden treatment, anneal, spring temper, quench etc.)
· Surface finish (peeling, gridding, polishing)
· Logistics service
· Customized packing service (also for exporting)
· Import and export (XUNSHI is certificated)
· Document translation
· Hard-to-find material sourcing
Customers of XUNSHI
Customers of XUNSHI are all over China (Taiwan and Hong Kong included). And we are exporting to USA, Canada, Italy, UK, Poland, Greece, Russia, Turkey, Iran, Israel, South Africa, South Korea, North Korea, India, Argentina, and Brazil and so on. Customers from 30+ countries trust us.
Where is XUNSHI
A- XUNSHI is in Huaqiao, Kunshan, 215332 China, which is very closed to Shanghai.
B- Xunshi is around 80KM from Shanghai Pudong International Airport (PVG).
C- 20KM from Shanghai Hongqiao Airport
D- 20KM from Shanghai Hongqiao Railway Station
E- You can contact XUNSHI sales for a pickup service.