Home Companies Shanghai Hongshi Mechanical Co., Ltd

No Oil Deposits Mitsubishi Lancer Spark Plugs Through Hot - Pressing Assembly Line

Active Member

Contact Us

[China]

Address: Jiasongbei Road. Jiading qu Shanghai . China.

Contact name:

Shanghai Hongshi Mechanical Co., Ltd

No Oil Deposits Mitsubishi Lancer Spark Plugs Through Hot - Pressing Assembly Line

Country/Region china
City & Province shanghai shanghai
Categories Other General Mechanical Components

Product Details

Auto Spark Plugs Mitsubishi Colt Galant Lancer 2.0L 1.5L (1988-) MS851417

 

Product Description                                                                            

 

1, Model No : DSP1022

 

2, OE NO / (Part number) : MS851417 / MS851178 / MS851237 / MS851187 / OE028 / BPR 5EA-11 / W 16 EPR11

 

3, Test capability : Salt Spray Test ,OK / High Temperature Endurance,OK

 

4, Power : Powerfull Withstand high temperature and high pressure

 

5, Inspection : 100% inspection

 

6, warranty : 1 Year / 50000 km

 

Assembly production                                                                         


1, through the automatic powder machine, the amount of resistance powder (with Bosch the same supplier) + center electrode + screw + expansion powder into the finished ceramic insulator inside, after heating, the internal structure of the spark plug has been formed.
 

2, after forming the need for internal voltage test, after 25000V high voltage on each of the detection of whether the breakdown of insulation and leakage, excluding unqualified products.
 

3, through the hot-pressing assembly line, the insulator and iron shell welding. And we are using hot riveting welding technology, this technology is currently Bosch's spark plug is also being used. Because the welding is the need for heating, so in the hexagonal screw will be under a circle of light blue halo. The NGK is the use of cold riveting technology, so the insulator and iron shell where there will be a small layer of pale white powder.

 

4, after assembly into the finished product, will be simulated air pressure detection, simulation of the engine cylinder operating pressure, the finished product installed into the test center electrode and the distance between the side of the electrode to achieve the ignition requirements of the engine to detect its performance and quality.
 

5, the detection of quality problems of finished products, for packaging.

 

Fit Model                                                                                             

 

MITSUBISHI COLT III (C5_A) 1.3 12V (C51A)1299554Hatchback1988-1992
MITSUBISHI COLT III (C5_A) 1.5 (C52A) CAT1468664Hatchback1990-1992
MITSUBISHI COLT III (C5_A) 1.5 GLXi (C52A)1468624Hatchback1988-1992
MITSUBISHI COLT IV (CA_A) 1.3 GLi 12V (CA1A)1299554Hatchback1992-1996
MITSUBISHI COLT Mk V (CJ_, CP_) 1300 GL,GLX (CJ1A)1299554Hatchback1996-2000
MITSUBISHI COLT Mk V (CJ_, CP_) 1500 (CJ2A)1468694Hatchback1995-2003
MITSUBISHI COLT/RODEO (K3_T, K2_T, K1_T,) 3.0 i 4WD29721096Pickup1990-1996
MITSUBISHI COLT/RODEO Platform/Chassis (K3_T 3.0 i 4WD29721096Platform/Chassis1990-1996
MITSUBISHI ECLIPSE I (D2_A) 2.0 i 16V (D22A, D27A)19971104Coupe1991-1995
MITSUBISHI ECLIPSE II (D3_A) 2000 GT 16V19971574Coupe1995-1999
MITSUBISHI GALANT IV (E3_A) 2.0 (E39A, E38A, E33A)1997774Hatchback1989-1992
MITSUBISHI GALANT IV Saloon (E3_A) 2.0 (E39A, E38A, 1997804Saloon1987-1992
MITSUBISHI GALANT IV Saloon (E3_A) 2.0 (E39A, E38A, 1997774Saloon1989-1992
MITSUBISHI GALANT IV Saloon (E3_A) 2.0 GTi 16V (E39A, 19971074Saloon1988-1992
MITSUBISHI GALLOPER (JK-01) 3.0 V629721046Closed Off1998-2003
MITSUBISHI LANCER IV (C6_A, C7_A) 1.5 (C62A)1468624Hatchback1988-1992
MITSUBISHI LANCER IV (C6_A, C7_A) 1.5 12V (C62A)1468664Hatchback1989-1992
MITSUBISHI LANCER IV Saloon (C6_A) 1.51468614Saloon1989-1990
MITSUBISHI LANCER IV Saloon (C6_A) 1.51468654Saloon1990-1992
MITSUBISHI LANCER IV Saloon (C6_A) 1.5 (C62A)1468624Saloon1988-1992
MITSUBISHI LANCER IV Saloon (C6_A) 1.5 12V (C62A)1468664Saloon1989-1992
MITSUBISHI LANCER IV Saloon (C6_A) 1.5 GLS1468634Saloon1989-1992
MITSUBISHI LANCER Mk VI (CJ-CP_) 1.3 12V (CK1A)1299554Saloon1995-2003
MITSUBISHI LANCER Mk VI (CJ-CP_) 1.5 (CK2A)1468694Saloon1996-1999
MITSUBISHI LANCER V (CB/D_A) 1.31298554Saloon1992-1995
MITSUBISHI LANCER V (CB/D_A) 1.3 (CB1A)1299554Saloon1992-1996
MITSUBISHI MINICA (H3_) 0.7657293Hatchback1993-1998
MITSUBISHI MIRAGE Saloon (CK_A) 1.5 (CK2A)1468814Saloon1995-1999
MITSUBISHI PAJERO I (L04_G, L14_G) 3.0 V6 (L141G, L1429721046Closed Off1988-1990
MITSUBISHI PAJERO I (L04_G, L14_G) 3.0 i 4WD29721056Closed Off1988-1991
MITSUBISHI PAJERO II (V3_W, V2_W, V4_W) 3.0 V6 4WD 29721106Closed Off1990-1995
MITSUBISHI SHOGUN II Open Off-Road Vehicle (V2_ 3.0 V6 29721106Open Off1990-1995
MITSUBISHI SHOGUN II Open Off-Road Vehicle  3.0 V6 24V 29721336Open Off1994-2000

 

Maintenance analysis                                                                           

 

1, the normal working conditions: the top of the insulator was light brown, no fuel or oil deposits.

 

2, carbon deposition: the surface of the black sediment, indicating that the mixed gas is too thick, weak ignition or calorific value is too low. So it is recommended to check the fuel and ignition system of the engine before replacing it.

 

3, the electrode burned: the calorific value is not correct, or the mixture is too thin or too early ignition time, waste recycling system and the ignition line of mutual inductance may lead to early ignition.

 

4, the engine jitter analysis: * Idle jitter 1, intake manifold or more valve leakage; 2, throttle and inlet fouling too much; 3, idling control element failure; 4, nozzle clogging or sealing bad ; 5, ignition coil high-voltage line aging failure; 6, spark plug leakage, coke, the gap is too large. 3, the transmission shaft bending deformation; 4, oil blockage, poor oil; 5, the valve damage, cylinder pressure uneven. 2, the tire pressure is not balanced; 3, 4, the ignition coil energy is insufficient; 5, the spark plug is attached to the oil dirt, gap fire, and the fire is not enough, * Occasional flameout 1, poor fuel supply, fuel injector or oil block; 2, the sensor failure; 3, motor failure.

 

Engine knocking phenomenon                                                           

   

    Engine knock is an engine abnormal combustion (overheating combustion) phenomenon, knock is usually very serious, if it is in high-speed high-load continuous and serious knock, not a minute, Spark plug and piston melting, serious even the cylinder and the engine body will be blown wear. There are six reasons: Ignition time premature - Ignition is too early, means that the piston before the deadline to establish the pressure, will hinder the piston rise, lack of power, because the piston to overcome the resistance to reach and cross the top deadline. It is possible in the intake valve is not completely closed when the combustion gas poured into the intake pipe burning, called temper, but also very scary. So to adjust the ignition time. The engine there is a serious carbon deposition - fuel or oil quality is not good, so that burning is not good, resulting in excessive carbon deposition, so to clean up the engine in time. Air-fuel ratio (A / F) is too low - air-fuel ratio, which represents the mixing ratio of air and fuel. Air-fuel ratio is an important parameter when the engine is running, it has a great impact on the exhaust emissions, the engine's power and economy, and this should check the oxygen sensor first. Cooling and cooling system work poor - cooling water due to leakage, infiltration or evaporation and reduce the natural heat away from the body will be reduced, so that the engine accumulated heat too much. The same heat sink device will make the engine heat load is too large, but also make the engine knock, timely inspection of cooling water, heat sink. Turbocharged vehicle turbines are pressurized high - turbocharged in general will allow the temperature of the front cabin to be higher and adjust the turbine pressure control device. Do not tighten the spark plug - according to the torque requirements to install the spark plug, if the spark plug did not tighten, will leak combustion gas, loss of power at the same time will lead to early ignition, causing knocking phenomenon. When this happens, remove the spark plug and observe the gasket. To determine whether our spark plug tightened, it depends on whether the sealing gasket pressure down

 

FAQ (Fluently Asked Questions)                                                          

 

Q1. If we don't find the model type here, Please tell us.

   1, Please send us your OEM number.

   2, Please send us your photo and products size if you have.

   3, Please tell us your exact car model if you do not have photo or OEM number.

 

Q2. What is your sample policy?
   1, We can supply the sample if we have ready parts in stock, but the customers have to pay the sample cost and the courier cost.

 

Q3. Do you test all your goods before delivery?
   1, Yes, we have 100% test before delivery.

 

Q4. What is your terms of payment?
   1, T/T 30% as deposit, and 70% before delivery. We'll show you the photos of the products and packages before you pay the balance.
 

Hot Products

Auto Spark Plugs Nissan Almera Sunny Renault Clio 1.2L 1.6L (1991-) 22401 12E15 1, OE Number or ...
Auto Spark Plugs Honda Accord Prelude 1.3L 1.6L (1979-) 98079-55146 1, OE Number or Parts Number ...
Auto Spark Plugs Mitsubishi Colt Galant Lancer 2.0L 1.5L (1988-) MS851417 Product Description 1, ...
Auto Spark Plugs Hyundai Elantra Kia Pride 1.3L 1.6L (1985-) KK151 18110 1, OE Number or Parts ...
Auto Spark Plugs Daewoo Korando Dodge Neon 2.0L 2.3L (1994-) 1621593003 OE Number Or Parts Number ...
Auto Spark Plugs Hyundai Kia Mazda Lancia 1.3L 2.0L (1989-) 71719244 Product Description Model No ...