(3) Detection Report

A. If the body temperature is below setting temperature (37.6 ℃), the green indicator light will be on. The representative has been tested, and the temperature of the current tested people is dynamically displayed on the display screen. As shown in the figure.

B. If the body temperature is over the setting temperature (free setting, generally: 37.3 ℃), the red indicator light will be on, and the machine will alarm.

Operating instructions for setting of through type temperature detection door

part I: assembly:

1.Remove the package, fix the door frame, and fix the temperature detection box on the door frame at the same time;

2. Plugin the power supply; the screen display is starting; waiting for 1-3 seconds, and "00.00" appears on the box screen, and it is red and green alternately, indicating that the start is completed;

Part II: debugging:

Generally, the factory is set to the quick passing mode, which is the mode used after the machine is started. The steps are as follows:

1. Click "setup menu" on the screen;

2. Click "mode setting" and set it to "mode 6" through "+" or "-"; when you see mode 6, it is normal;

Click "finish" on the screen; save through the above confirmation mode;

Next, we set the temperature deviation value and high temperature alarm value in this mode. The steps are as follows:

1. Set the bias value:

(1) Click "environment parameters";

See: 6.5 or 7.0; adjust by "+," - ";

This value is the increase or decrease adjustment of the test results. If the temperature is high, the parameter value will be reduced, otherwise, it will be increased.

(2) Click "confirm" again to save;

2. High temperature alarm setting;

(1) Click "alarm temperature 2";

(2) Adjust by "+," - ";

(3) Click "confirm" again to save;

(if it's already 37.5 degrees, it doesn't need to be noticed. This value is the alarm value of the temperature);

3. Alarm temperature 1 setting;

(1) Click "alarm temperature 1";

(2) Adjust by "+," - ";

(3) Click "confirm" again to save;

(the default value of the system is 35.0 degrees, i.e. when the measured temperature exceeds 35.0 degrees, the green light will be on);

4. Sensing distance setting;

(1) Click "alarm temperature 2";

(2) Adjust the sensing distance by "+," - ";

(3) Click "confirm" again to save;

(if it's already 55, don't worry about it. This value means that the temperature measurement program will be started at 55cm before the person reaches the temperature box);

5. Alarm duration setting;

(1) Click "alarm time";

(2) Adjust the sensing distance by "+," - ";

(3) Click "confirm" again to save;

(if it's 1500, don't worry about it. This value is the alarm time of abnormal temperature.)；

• Restore the factory settings;

(1) Click "restore factory";

The system will prompt whether to clear the statistical data. After selection, click OK to save;

After all parameters are set, click finish.

About the setting mode of temperature door and the setting of deviation correction in the mode:

Generally, when leaving the factory, it is set as the side head passing mode, which is the mode used after starting the machine. The steps are as follows:

Long press the middle key; (behind the detection box, there is a long hole, in which there are three small red buttons, the handle is put in, there is no power, do not be afraid, it can be operated with electricity);

See "1" on the number of digits on the screen；

Press the up and down buttons to "4". When you see 4, press the middle button. When you see "1" on the ten digits of the screen, you can adjust the mode by pressing the up and down buttons. Mode 1: side head through mode. It is also the factory mode.

Mode 2: side head passing mode;

Mode 3: stop and stay through mode; press the middle button to save;

In this step, the mode has been selected;

Next, we set the temperature deviation value and high temperature alarm value in this mode. The steps are as follows:

1. Set the bias value:

(1) Long press the middle key to see "1";

Press the middle key again to see: 6.5 or 7.0; adjust through the up and down keys;

Long press the middle key, look

(if it is 7.0, it will not be adjusted, that is, it will be defaulted to be this number first). Carry out the test, and this value is the increase or decrease adjustment of the test result. If the temperature is high, reduce this value, and try to debug.)

Press the middle key again to save;

2. High temperature alarm setting;

(1) Long press the middle key, and you will see "1" on the single digit;

(2) Through the up and down key adjustment, see "3";

(3) Press the middle key again, 37 will appear;

Adjust the setting to "37.5" by pressing up and down to increase or decrease;

(if it's already 37.5 degrees, it doesn't need to be noticed. This value is the alarm value of the temperature);

(4) Press the middle key again to save;

3. Sensing distance setting;

(1) Long press the middle key, and you will see "1" on the single digit;

(2) Through up and down key adjustment, see "6";

(3) Press the middle key again, 55 will appear; increase or decrease the sensing distance through the up and down keys;

(if it's already 55, don't worry about it. This value is that when a person reaches 55cm before the temperature box, the box will be opened for temperature measurement);

(4) Press the middle key again to save;

4. Alarm duration setting;

(1) Long press the middle key, and you will see "1" on the single digit;

(2) Through up and down key adjustment, see "7";

(3) Press the middle key again, 1500 will appear;

(if it's already 1500, don't care. This value is the length of abnormal temperature alarm time);

(4) Press the middle key again to save;