MF-DM500WBSW BEAM SHARPY MOVING HEAD LED STAGE LIGHT
Specifications:
OPERATING MODE
| DMX Control | DMX mode, receive DMX signal, RDM signal |
| Auto Run | Fixture run automatically according to built-in programs |
| Sound Control | When the fixture detects a strong sound, the fixture automatically
runs a scene according to the built-in program, otherwise it will
stay the last scene |
| Scene Mode 01 | runs in a set scebe, which supports most of the custom editing of
10 scenes. |
1~10 | outputs the specified scene |
Auto | Automatically loops the output scene in the set scene time
(non-zero) order, and the scene with time 0 automatically ignore |
| M/S Choose | Master and slave selection, non-DMX mode takes effect, select the
mode of data output, fixture detect DMX cable state automatic
switch output, prevent data conflicts |
| Master | Fixture runs built-in program. If DMX has no signal, it outputs
data (synchronization), otherwise it does not output data. |
| Slave | Fixture runs built-in program and do not output data |
| Auto | If DMX has no signal, the fxiture will runs built-in program.
Otherwise, the fixture will run in DMX Mode(follow DMX). |
| Lamp Switch | (Lamp light source) pop-up confirmation dialog box, select "SURE"
to confirm the current operation, turn on or off the lamp, switch
time interval limited to 30 seconds |
| Off | The current lamp output is off |
| On | The current lamp output is turned on |
DISPLAY SETTING
Language | Display language settings |
English | English display |
Chinese | Chinese display |
Screen Saver | Set screen 30 seconds without operation, the screen's display
content or method. |
OFF | Keep the last operation page |
Mode1 | Black |
Mode2 | Black screen, showing the address code of the current fixture in
the lower left corner. |
Mode3 | Display trademark information, address code and operation mode. |
Screen Rot | Set the display direction of the screen. |
OFF | No reverse display |
ON | Reverse display |
DMX Indicate | Set the indication mode of DMX signal indicator. |
Mode1 | When signal is bright, no signal is off. |
Mode2 | When signal is off, no signal is bright. |
Mode3 | When signal is flash, no signal is off. |
Screen Light | Set the screen backlight for 10 seconds without operation |
1~10 | 10 |
Common Fault:
According to some common faults, the corresponding solutions are
put forward.Any unsolvable problems should be dealt with by
professionals.Disconnect the light fixture before maintaining it.
1. Light bulb is not on
Check that the voltage that matches the light fixture is installed;
Check whether the lamp supply power connection or control switch is
in bad contact;
Check if the power supply is insufficient;
Check that the DMX512 controller is sending instructions.
2. The light fixture does not accept control from the console after
normal reset
Check luminaire digital start address value and function options
are correct;
Check whether the connection of communication control line is
correct, the communication line is too long or has been
interrupted;
Check whether the control equipment is invalid, check whether the
serial access signal amplifier is invalid;
Check whether the communication line is too long or other equipment
interferes with each other;
Optimize wiring, shorten the length of control signal lines, high
voltage and low voltage lines separate wiringAdd signal amplifiers;
Signal line using high-quality shielded twisted pair wire;
Connect the signal terminal resistor (120 ohm) at the end of the
lamp.
3. Luminaire does not start
Check that the power supply parameters are consistent with the
lamp;
Check the poor contact caused by extrusion deformation, vibration
and moisture of internal parts in the long distance transportation
process or fall off.Please check whether the internal wire integration connector of the
lamp has fallen off or loosened.
Check whether the electronic components of the lamp (such as
electronic transformer, PCB board, motor control board, etc.) are
loose, short circuit and burned out.
4. When working, the action of the X or Y axis of the lamp is not
normal
Follow the previous step to check them one by one;
Check whether the transmission belt corresponding to the X and Y
axis directions in the lamp falls off and breaks;
Check whether the data feedback receiver (optocoupler)
corresponding to the X and Y directions in the lamp is damaged;
Restart the machine and reset it once.
Panel Operation:
BRIEF
The light panel diagram show as Figure 3, above area is fixture
description, below area show fixture real-time status, such as DMX
cable status, lamp status, error or information(ps. when there are
message hav't been checked, echo 'ERR' in status bar, otherwise
echo 'NOR'). Display & operation just like 'Android operation
system', when select or set item value, system save the settting
immediately. RDM protocol is embed in fixture, user set DMX address
via cable using the controller surpport RDM function. when fixture
was search by controller, displayer will echo 'RDM' indicate this
RDM is work.
OPERATION
Operate fixture with touch or encoder/button
The left area is TFT Displayer and touch(product which support
touch), chick item or value with finger will to complete operation of set light
setting(parameters) or view light state.
The area on the right hand side is rotary encoder with button or
key, As auxiliary input interface, if fixture disable touch function, the encoder/key can
been choose to set or view the item, and then press the encoder button/key to confirm the
selection, rotary
encoder or push key again set the parameter value, finally, Press
encoder button/key one again to save value or setting.Parameter value settingWhen the selected item is value need to been modified, the dialog
shown in Figure 4 will pop up.
Modify value:Can quickly modify value via pull the slider to the desired
position, or click the button of 'up' or 'down' whit finger on the right side to
set the exact desired value, another way is roll encoder on the right hand side of panel.
Apply value:When Value had been modified, Then press the bottom of 'apply' in
the left corner to apply to the light, but haven't saved;
Save Value:Any time, click on the lower right corner of the "OK" button, the
setting will been saved into internal memory.
Boolean parameter setting
when the selected parameters is a Boolean value (such as ON or
OFF), can directly modify setting by chick corresponding item, the
setting will been saved right now.When the parameter is a key item, chick corresponding item, a
dialog shown in Figure 5 will been popup ask for the confirm. Chick 'sure' to confirm.
Sub Menu(Parameter)
Installation:
CABLE CONNECTION DMX
Use a cable conforming to specifications EIA RS-485: 2-pole
twisted, shielded, 120Ohm characteristic impedance, 22-24AWG, low
capacity. Do not use microphone cable or other cable
withcharacteristics differing from those specified.
Theendconnections must be made using XLR type3 or 5-pin male/female
connectors. A terminating plug must be inserted into the last
projector with a resistance of 120Ohm (minimum 1/4W)between
terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with
the metal casing of the connectors. The casing itself must be
connected to the shield braid and to pin 1 of the connectors.
RIGGING(OPTIONAL)
This equipment can be positioned and fixed by clamp in every
direction of the stage. Locking system makes it easy to fasten to the bracket.
Attention! Two clamps is needed to fix the equipment. Every clamp
is locked by fastener of 1/4 kind. Fastener can only be locked clockwise.
Attention! Fasten a safety string to the additional hole of side
aluminum piece. The secondary accessory can not hang on the delivery handle. Nip the
equipment on bracket.
Check if rigging clamp (not including the one inside) damaged or
not? If stand ten times weight as the equipment. Make sure the architecture can stand ten
times weight as all the equipments, clamps, wirings and other additional fixtures.
Screws for clamping must be fixed firmly. Take one M12 screw (Grade
8.8 or higher) to clamp bracket, and then screw the nuts.
Level the two hanging points at the bottom of clamp. Insert
fastener to the bottom, lock the two levers by 1/4 rotating clockwise; then install another
clamp.
Install on safety string which stands at least ten times weight as
equipment. Terminal of the accessory is designed for clamps.
Make sure pan/tilt lock unlocked or not. Keep the distance more
than 1M from equipment to flammable material or lighting source.
Applications:
Moving head lights are versatile lighting fixtures used in stage
productions, concerts, nightclubs, and other entertainment events.
They consist of motorized heads that can move horizontally and
vertically to direct light beams. They are used to illuminate
performers, create dynamic lighting effects, and enhance visual
displays.
Packing:
Product Name | Quantity |
| 1 PCS |
Power-line | 1 BASE |
| User Manual | 1 PCS |
FAQ:
Q1: What do you sell?
A1: We provide good quality of floodlight, high bay light,
explosion proof light, tri-proof light, downlight, and other
lighting products, as well as responsible services and reliable
after-sales warranty.
Q2: Is it OK to print my logo on led light product?
A2: Yes. We provide ODM and OEM services. Please inform us formally
before our production and confirm the design firstly based on our
sample.
Q3: How to deal with the faulty?
A3: During the guarantee period, we will send new lights with new
order for small quantity. For defective batch products, we will
repair them and resend them to you or we can discuss the solution
including re-call according to real situation.
Q4: Can I have a sample order for led light?
A4: Yes, we welcome sample order to test and check quality. One
sample or mixed samples are acceptable.
Q5: How long time to ship the goods if place an order?
A5: Usually 7 days for sample or small order,15 working days for
bulk order, but sometimes depend on the order quantity.
