Tri Proof Light IP20 Microwave Motion Sensor With ON OFF Function

Tri Proof Light IP20 Microwave Motion Sensor With ON OFF Function

Tri-proof Light Microwave Motion Sensor 2.5-6m General Altitude Installation

Features:

1. 2.5-6m general altitude installation.

2. 5.8G microwave motion sensor with dimming function.

3. Suitable for tri-proof light and liner light.

4. Supports DIP switch programming and remote control.

5. Smart swithes and dimmers when detecting movement of objects.

6. IP 20 with 5 years warranty.

7. Sensitive and reliable.

Product Description

      ON/OFF Control          Detection Area        Daylight Threshold           Stand-by Period

    Warranty 5 years               Hold Time          Stand-by Dimming Level      8-15m Highbay

Detection Range

This figure indicates the maximum distance at the highest mounting height with 100% sensitivity.

Typical installation height 8-15m.

Mechanical structure

With nine DIP switch poles to set all parameters

With six poles to easily connect with LED driver and power supply

With two installation hole, easily fixed to the lighting fixture for end user

The separation of the sensor can be  small to fit into the LED PCB board

Wiring diagram

Dimensions (mm)

DIP Switch Setting

Detection Area:

In this area, movement will be detected and able to trriger the sensor,100% detection area is known as the strong sensitivity.

Hold Time:

The period of light keeping 100% brightness after moving objects leave the detection area.

Daylight Threshold:

Definition of the ambient brightness;only when the ambient brightness is lower than the preset spcific lux amount,the sensor will work;when it's preset as "disable",the sensor works everytime it detects motion regardless the ambient brigtness.

Stand-by period:

The period of light keeping low output before it's compeletely switched off,when it's preset as"∞" the light always keep at low output if no movement in the detection area and doesn't turn off.

Stand-by dimming level:

The difinition of low output in the stand-by period.

Application Demo 

1. Automatically ON/OFF function:

Light on when detect movement and off after people leave at night. Applications: Corridor, Staircase.

With sufficient daylight,                 With insufficient daylight,             After the last detection and
even when motion detected,          when motion detected, light ON.   the present hold time
light remains OFF.                                                                               elapsed, light OFF.

2. No daylight function
The daylight threshold is set to "Disable".
Light on when detect movement, After people leave, Light off after stand-by period.
Applications: Dim places such as Basement Parking, Underpass.

When motion is detected,              After people leave the detection    After the last detection and
the sensor will switch on the         area, light remains 100%                the present hold time
light to 100% brighteness.             brightness within hold time.          elapsed, light OFF.

3.Function Demo-Dimmable control/Corridor function

With sufficient daylight,    With insufficient          After the last detection,      After the stand-by period

even when motion           daylight when               the light will be dimmed     light off.

detected,light                  motion detected,          down to the stand-by 

remains off                      light on,                       dimming level

                                                                           (10%,20%,30% or 50%)

                                                                            after holdtime.

User Notes:

1.Microwave can penetrate walls or glass thinner than 20cm and attenuate if thicker than 20cm.
2. The driver voltage shall be stable and float within 10%.
3. Detection area will be affected by speed of motion, mounting height and movement volume.
4. Conduct test on sunny days without the lampshade which will affect the tested lux value.

Memory & Apply Mode

1. Press "ON/OFF button" to turn on the light or off.

2. To reset the parameters, Please follow the steps as below:

Step 1 - Press ON, to turn on the light if it was off at the start.

Step 2 - Press "Start" to the well-setting sensor.

Step 3 - Press the button of Detection range, Hold time, Stand-by dimming level,

Stand-by period and Daylight threshold one after the other in sequence (Press "+/-" to

set parameters).

Step 5 – Press “Memory” to memorize the settings.

Note: The interval of each parameter setting shall be controlled within 30s.

Isolated Setting Mode

1. Press "ON/OFF button" to turn on the light or off. Press "Scene", the remote will

activate settings that were saved last or remain at the factory default settings.

2. To reset the parameters, Please follow the steps as below:

Step 1 - Press ON, to turn on the light if it was off at the start.

Step 2- Press any button of "Scene", Test" and "Apply" to begin the sensor detection

mode.

Step 3 - Press the button of Detection range, Hold time, Stand-by dimming level,

Stand-by period and Daylight threshold one after the other in sequence.

3. To programme other lights in the array that have similar sensors to the same

programme.

Step 1 - Press "ON" to the second sensor

Step 2 - Press "Apply"

Notes:

1. Settings will be saved automatically and remain until you press reset again.

2. Light will flicker when setting each parameter.

3. The icon will flash when setting the corresponding parameter.