Home Companies Shenzhen HAISEN Technology Co.,Ltd.

LED Emergency Converter Suit For LED Fitting With External LED Driver

Shenzhen HAISEN Technology Co.,Ltd.

Contact Us

[China] country

Trade Verify

Address: 13th Floor, C1 Building, Songshan Lake Intelligent Valley, Liaobu Town, Dongguan City, 523808, Guangdong.

Contact name:Evelyn Chow

Inquir Now

Shenzhen HAISEN Technology Co.,Ltd.

Verified Suppliers
  • Trust
    Seal
  • Verified
    Supplier
  • Credit
    Check
  • Capability
    Assessment

LED Emergency Converter Suit For LED Fitting With External LED Driver

Country/Region china
City & Province dongguan guangdong
InquireNow

Product Details

LED Emergency Converter Suit For LED Fitting With External LED Driver

 
Features

  • Constant output power
  • Used with lithium battery
  • Suits forLED fitting with external LED driver
  • Accessary test switch and LED indicator
  • With multi-protection function:

​         -battery overcharge protection
         -battery over-discharge protection
         -output overload protection
         -short-circuit protection 
 
 
Parameter Table

 

Input voltage220-240 Vac 50/60Hz
Input Current0.06A(Max) 230V AC
Power Factor0.5
Max.output current170mA
Battery charging current200mA(Max)
Battery charging time24h(Max)
LED indicator status

Green on: Battery charging or fully charged
green off: Emergency mode

Working temperature0-60°C
Maximum shell temperature75°C
Storage temperature-20-60°C 
Electric strength3000Vac 5mA(input to output)
IP RatingIP20
Warranty

3 Years 

 

 

 

Model Selection table

 

Model NoInput voltageOutput voltageOutput currentLithium batteryEmergency timeEmergency power
ES-EOD02-01220-240Vac 50/60Hz20-60V DC100-30mA1800mAh/7.4V3Hrs2W
ES-EOD03-01220-240Vac 50/60Hz20-60V DC150-50mA2000mAh/7.4V3Hrs3W
ES-EOD04-01220-240Vac 50/60Hz20-60V DC200-60mA2500mAh/7.4V3Hrs4W
ES-EOD05-01220-240Vac 50/60Hz20-60V DC250-80mA3000mAh/7.4V3Hrs5W
ES-EOD06-01-1H220-240Vac 50/60Hz20-60V DC300-100mA1800mAh/7.4V1H6W

 


Dimension (Unit:mm)



Operation Instructions
1. Connect the wires according to the wiring diagram.
2. Power on L and N, and close the switch S1. At this time, the load light will turn on, the indicator light of the emergency power supply will turn green, and the emergency power supply is charged normally. Turn off this switch S1, the load light will go out.
3. Simulated emergency: close switch S1, turn on the load light, and then press the switch (TEST SWITCH), then switch to emergency power supply mode, the green light of the emergency power indicator will go out. Then  release the switch (TEST SWITCH), at this time it should be switched to external drive power supply, the green light of the emergency power indicator will light up.
4. Power failure and incoming call, the phenomenon should be the same as simulated emergency.

 


Battery Application Notice

1.The battery should be recharged and discharged semiannually in normal use conditions.
2.Do not connect to the circuit when the battery is not use to prevent over-discharge of the battery due to self-consumption of the circuit board.
3.Please keep the battery from the heat source when installing and using, and only be allowed to use in certain working temperature range.
4.The battery should be stored in a cool and dry environment.
5.After long time storage, the battery is cycled every 6 months as required.

Hot Products

The Microwave sensor HD05V-CRH with DIP switch and On/Off function Features Dual setting by DIP ...
Small Size DIP Swicth Sensor with UL And FCC Certification *HD401S 1 specification.pdf* Features: ...
Detached Design Dimmable Sensor HD405V-CRH with UL And FCC Certification *HD405V-CRH specification...
15M Highbay UL Sensor HD406VRH Suitable for UFO With On/Off Function *HD406VRH ON&OFF specification...
HD07VR-MH-B Highbay Bluetooth Sensor with UL Certification Dimmable Funnction *HD07VR-MH-B ...
HT36V Motion Sensr And Driver 2 in 1 Product with Dimmable Function *HT36V.pdf* Features: 5.8GHz ...