|
[China]
Trade Verify
Address: 101-1101, Building 17, Dianda Guyuan Industrial Park, Mashantou Community, Matan Street, Guangming District, Shenzhen
Contact name:June Zhao
Shenzhen Merrytek Technology Co., Ltd. |
|
Verified Suppliers
|
|
|
KL40V-PDiiV 40W Constant voltage driver with 24V output
【Product Feature】
【Parameter】
| Series | Name | KL40V-PDiiV1 | |||||
| Input | Voltage range | 198~264Vac 50Hz /60Hz | |||||
| Rated supply voltage | 220~240Vac 50Hz /60Hz | ||||||
| DC voltage range | 200~240Vdc | ||||||
| Input current | 0.21A Max.@230Vac | ||||||
| Inrush Current | 15A (Half current pulse width 100US) @230VAC | ||||||
| Power factor | ＞ 0.95 (@230Vac,100% load) | ||||||
| Total harmonic distortion | Typical: 16% (@230Vac, 100% load) | ||||||
| Stand-by power | ≤0.5W | ||||||
| Efficienc(@230Vac,100% load) | 89%Max | ||||||
| Wiring method | Push terminal, wire cross section:0.5-1.5mm2 | ||||||
| Loop-in&Loop-out quantity | 30PCS(@230Vac) | ||||||
Automatic circuit breaker (Calculate current in the wire) | type | B10 | B13 | B16 | B20 | B25 | |
| Number | 35 | 45 | 55 | 70 | 86 | ||
| type | C10 | C13 | C16 | C20 | C25 | ||
| Number | 20 | 25 | 30 | 42 | 50 | ||
Output Output | Operating mode | Constant voltage | |||||
| Load type | LED | ||||||
| Flickering / Flickering-Free | Flickering-Free | ||||||
| Start up time | <1s (@230Vac) | ||||||
| Load output voltagerange | 24V CV | ||||||
| Load output current | 1.67A Max. | ||||||
| Full load output power | 40W Max. | ||||||
| Minimum load | 3W | ||||||
| Output current/voltage tolerance | ±5% | ||||||
| Wiring method | Push terminal, wirecross section:2*0.5-2.0mm2 | ||||||
| Control Method | Primary PUSH Dimming | Primary PUSH dimming (Max. lead wire length:20m) | |||||
| 1-10V(0-10V)Dimming | 1-10V dimming(Port current＜1mA), (Max. lead wire length:20m) | ||||||
| Dimming Range | Primary PUSH & DALI dimming: 0%-100% 1-10V dimming:1%-100% | ||||||
| Secondary PWM dimming | 1-10V port PWM dimming (3KHz-8KHz) | ||||||
| Potentiometer | Yes, 100kΩ | ||||||
| DALI function | DALI dimming (Max. lead wire length:300m) | ||||||
| Exception Protection Requirements | Output over temperature protection | Yes, reset power on to recover | |||||
| Output short circuit protection | Yes, reset power on to recover | ||||||
Operating Environment | Operating temperature/ humidity | -25℃~50℃ Humidity:85% (Non-condensing) | |||||
| Storage temperature/ humidity | -40℃~80℃, Humidity:10%–95% | ||||||
| Max. case temp(Tc) | 85℃ | ||||||
| Safety & EMC | EMC standard | EN55015, EN61547, EN61000-3-2, EN61000-3-3 | |||||
| DALI standard | IEC62386-102, IEC62386-207 | ||||||
| Safety standard | EN61347-1, EN61347-2-13 | ||||||
| Certification | CE | ||||||
| Withstand voltage | 3750Vac, 5mA, 60s (Input “L N”- Output “SEC”) | ||||||
| Others | Degrees of protection | IP20 | |||||
| Type of protection | Class II | ||||||
| Installation type | Independent installation | ||||||
| Installation dimension | 150*52*28mm | ||||||
| Memory function | Yes, (PUSH with memory function) | ||||||
| PUSH dimming synchronization | 20 units Max. | ||||||
| Packaging requirements | Instruction+clapboard+outer carton(K=A) | ||||||
| Weight | 300g | ||||||
| Life | 5 years @Ta 100% load | ||||||
| Note: All parameters are tested at the input voltage of 230Vac and 25 degree environment unless specified. | |||||||
【Dimension (Unit:mm)】
【Wiring Diagram】
 Fig. A DALI Dimming |  Fig.B Push Dimming |
| |
【Derating】
【Dimming curve】
【ON/OFF & Description of Dimming Operation】
A. Short press the PUSH switch (short press time 0.1S-1S), the LED driver will turn on or off.
B. Dimming:
Press and hold the PUSH switch (1S-8S), the LED driver can achieve dimming, brightening or dimming, the dimming range is 2-100%.
C. Memory:
PUSH dimming has dimming memory function.
D. Dimming synchronization:
The power connected to the same PUSH switch can be synchronized by pressing and holding the PUSH switch for longer than 15S
E. DALI dimming mode:Connect the power supply to the DALI system, and it can be dimmed by the DALI host. The dimming range is 0-100%.
F. Constant voltage dimming drivers cannot be used in lamps with constant current circuits.
