|
[China]
Trade Verify
Address: 101-1101, Building 17, Dianda Guyuan Industrial Park, Mashantou Community, Matan Street, Guangming District, Shenzhen
Contact name:June Zhao
Shenzhen Merrytek Technology Co., Ltd. |
|
Verified Suppliers
|
|
|
ML30C-PV 1x30W PUSH / 1-10V Dimmable LED Driver For LED Panel
Light 250 – 700mA 103x67x22mm
Features
1,Stand-by power below 0.5W
2, ML30C-PV is multi-current supply, selection of output
current through DIP switch
3, 12Vdc /24Vdc is not constant voltage strictly, it is a limit that
the output voltage will not exceed 12Vdc /24Vdc when output 700mA.
So the output load range by 12Vdc( 0-700mA )is 8.4W max
4. with 1-10V and push button
5, Flicker-free for whole dimming range
6, Jumper design for switching different dimming modes, it is
very convenient to select suitable
dimming mode as you required
7, Synchronization: thanks to the MCU programme, up to 15pcs
drivers should be controlled by the
same switch. This means there is no need for any additional
synchrony wire in larger installations,
where many drivers should be controlled by one switch
8, Memory function: The driver has built-in permanent memory
against power failure. Lights can
return to previous dimming level when switch off and on again, even
at mains restores
9, Maximum length of the cable, from switch to last driver is 20m
10, Factory setting: 100% dimming level and 250mA output
11, Dim via a potentiometer is your choice
12, Protection: Short circuit / Over voltage / Over temperature
13, 5 years guaranty
14, Support master-slave grouping net working
15, Derating current for over high ambient temperature
Mechanical Specification
Dimming Operation:
1.Push button switch for dimming (see wiring diagram, Fig A &
Fig B)
2.1-10V dimming (see wiring diagram, Fig C)
The driver supports any active 1-10V dimmer. When the dimming
signal is less than 0.8V ~ 1V or short the dimming wires, the
output of LED driver could be completely switch off, see Fig C
Wiring Diagram:
Specifications:
| Input voltage | 220-240Vac |
| Input frequency | 50-60Hz | |
| Input current | 0.18A max | |
| Power factor (Note 1) | ≥0.90 | |
| Efficiency(Note1) | ≥84% | |
| Stand-by power (Note 2) | ≤0.5W | |
| Output current/ voltage | 250mA 6~60V DC 15W max.; 350mA 6~60V DC 21W max |
| Output load range | 30.2W Max. | |
| Current accuracy | ±5% | |
| Dimming mode | 1-10V, PUSH | |
| Working temp.(Ta) | -20~50℃ |
| Surface temp.(Tc) | 85℃max | |
| Working humidity | 20~85%RH non-condensing | |
| Storage temp. | -40~80℃ | |
| Life time | ≥50000hours | |
| Isolation class | Class Ⅰ |
| Protection class | IP20 | |
| Over voltage | 300Vac, 2H | |
| Short circuit | Protection type; auto reset | |
| No-load | Protection type; auto reset | |
| Over temperature | Protection type; auto reset | |
| Safety | EN61347-1 EN61347-2-13 |
| EMC | EN55015, EN61000-3-2 | |
| EN61000-3-3, EN61547 | ||
| Approvals | SEMKO, CE, RoHS | |
| Withstand voltage | IN-OUT:3.75KVAC/5mA/1min | |
| Dimension (L x W x H) | 103x67x22mm | |
| Connection | Press-in type terminals, 0.75-1.5mm2 | |
| Note: | |
Applications
For LED panel light, LED down light, led strip, led tube etc…
Wire diagram
