|
[China]
Trade Verify
Address: Huadu District, Guangzhou City, Guangdong Province, China
Contact name:ZENG
YUEMI |
|
Verified Suppliers
|
|
|
Stainless steel medium-sized mechanical seals for chemical water pumps and papermaking industry GB104
Single seal / Unbalanced / Driving sleeve to drive / Independent of direction of rotation
The series is typical of the mechanical seal Spring, with various materials and face combination , in order to meet
various requirements.
Mediums to be sealed: water, oil, middle corrosion liquids and other mediums including solid granule
Pressure in the sealed chamber: ≤1.0MPa
Rotational speed: ≤3000r/min
(Linear velocity:≤20m/Sec)
Temperature in the sealed hamber: 0℃~ +180℃(FPM)
-30℃~+120℃(NBR) -40℃~+230℃(EPR)
-40℃~+230℃(PTFE) -40℃~+230℃(PTFE cover rubber)
Meet JB/T 1472-94 standard
| SPECI | d H6 | d1
| D1 H11 | D2 H8 | L | L1 ±0.5 | L2 ±0.5 | L3 |
| 104-25 | 25 | 42 | 35.5 | 45 | 62 | 43 | 14 | 14 |
| 104-28 | 28 | 45 | 38.5 | 48 | 63 | 44 | 14 | 15 |
| 104-30 | 30 | 52 | 40.5 | 50 | 68 | 49 | 14 | 15 |
| 104-35 | 35 | 57 | 45.5 | 55 | 70 | 51 | 14 | 17 |
| 104-40 | 40 | 62 | 50.5 | 60 | 73 | 54 | 14 | 20 |
| 104-45 | 45 | 67 | 55.5 | 65 | 79 | 60 | 14 | 25 |
| 104-50 | 50 | 72 | 60.5 | 70 | 82 | 63 | 14 | 28 |
| 104-55 | 55 | 77 | 65.5 | 75 | 84 | 65 | 14 | 30 |
| 104-60 | 60 | 82 | 70.5 | 80 | 84 | 65 | 14 | 30 |
| 104-65 | 65 | 92 | 80.5 | 90 | 96 | 74 | 17 | 35 |
| 104-70 | 70 | 97 | 85.5 | 97 | 101 | 76 | 19 | 37 |
| 104-75 | 75 | 102 | 90.5 | 102 | 101 | 76 | 19 | 37 |
| 104-80 | 80 | 107 | 95.5 | 107 | 106 | 81 | 19 | 42 |
| 104-85 | 85 | 112 | 100.5 | 112 | 107 | 82 | 19 | 42 |
| 104-90 | 90 | 117 | 105.5 | 117 | 108 | 83 | 19 | 43 |
| 104-95 | 95 | 122 | 110.5 | 122 | 108 | 83 | 19 | 43 |
| 104-100 | 100 | 127 | 115.5 | 127 | 108 | 83 | 19 | 43 |
| 104-110 | 110 | 141 | 130.5 | 142 | 132 | 105 | 21 | 60 |
| 104-120 | 120 | 151 | 140.5 | 152 | 132 | 105 | 21 | 60 |
Technical Parameters
| Temperature | -30℃~+200℃ |
| pressure | ≤2Mp a |
| Speed | ≤10m/s |
| Medium | water |
Materials
| Rotary Ring | SiC/VIT |
| Stationary Ring | SiC/VIT |
| Spring | SUS304/SUS316 |
| Stationary Seat | SUS304/SUS316 |
| Secondary Seal | VITON/EPDM |
| Rotary Ring Holder | SUS304/SUS316 |
Preperation:
1. Shaft Outside Diameter is within tolerance +-0.05mm
2. Shaft run out <0.1mm
3. Shaf end float <0.13mm
4, No sharp edges on the shaft over the o ring
Note:
During the installation,don't scratch or damage the o ring.lf
anything is damaged,please contactwith Us to replace a new one.
Installation in strucstions:
1. The full set of cartridge seal is cleaned and exactly passed
leakage examine before sale.Inorder to avoid damage,don't
disassemble and clean the parts again before fixing.
2 The fitting allowance between the seal and shaft is dl h6 0.8,and
there should be leading-inedge at the end of shaft.The outside
diameter of shaft at the position of screw should be 01 0.2mm
smaller,resisting the screw over-tighten.Lubricate the shaft with
oil
3. Place the cartridge seal into the pump chamber,then:
A: Tighter four screw bolts of flanges,ensuring the medium leading
in hole"G"at the top Position
B : Tighter four set screws and position the shaft sleeve on the
shaft.
C: Remove four gauge plates.Please keep them and they wil be used
in future installation and
disassemble.
D: Connect the medium lead_in pipe with hole"G"in order to flush
away the friction heat and
flushing the seal chamber when pump running.
Note:
ter complete the installation,turning the shaft by hand to check
for the rotationi he shat could not rotate smoothily,seal had been
improperly installed.
We would like lo sincerely ooperale with Clients to supply high qually products and senice We beleve in establishing a long:erm cooperalive relalionshipis lhe key to suceess
1.Who are we?
We are based in Guangdongsheng, China, start from 2014,sell to
Western Europe(30.00%),North America(30.00%),Southeast
Asia(20.00%),South America(10.00%),Mid East(10.00%).
2.How can we guarantee quality?
Always a pre-production sample before mass production;
Always final Inspection before shipment;
3.What can you buy from us?
Mechanical seals for pumps from various world-renowned brands
4.Why should you buy from us not from other suppliers?
We are a manufacturer with 15 years Industry experience.
5.What services can we provide?
Accepted Delivery Terms: FOB,CIF,EXW,DDP,Express Delivery；
Accepted Payment Currency: USD,EUR,JPY,CAD,AUD,HKD,GBP,CNY,CHF;
Accepted Payment Type: T/T,L/C,MoneyGram,Western Union,Cash;
Language Spoken:English,Chinese,Spanish,French,Russian,Italian K
