2 in 1 Garden Plant Soil Moisture Sunlight PH Meter Tester Digital Analyzer Garden Tool for Plants Crops Flowers

2 in 1 Garden Plant Soil Moisture Sunlight PH Meter Tester Digital Analyzer Garden Tool forPlants Crops Flowers Hydroponic MAPH-009

Functional features:
The tool plant owners, gardeners can't live without!
2 IN 1 moisture light & PH meter Soil analyzer meter.
For outdoor & indoor plants, gardens & grass lawn.
Take the for guess work out of your daily garden watering light and moisture.
Save water, energy and keep your plants, lawn, flower in top condition.
Measures moisture at root level.
Prevents over and under watering
Scientifically accurate.
Easy to use, just insert and read.
No battery required, simple and convenient to use
Simply insert the meter into the soil, switch to the setting you want to measure and read the scale.
To avoid damaging the electrode, please clean the electrode after each use

Specifications:
Material: Plastic
Soil PH Measurement Range: About 0 - 9.0 pH
Accuracy: About ±0.25 pH(20℃)±0.2 pH (Suitable for farm or education experiments)
Working Temperature: About 0 - 50°C(32-122°F)
Calibration: Manual point 1
Measurements: About 18cm/7.09" X 6cm/2.36"
Length of Probe: About 8.2cm/3.23"

Notes:
1. Soil pH value is a very important factor for the quality of crops.
2. Most of crops cannot survive in too acid or too alkaline soil.
3. Get the right pH reading for your Crop is very important.

Using Method:
1. Measuring soil pH and moisture, as far as possible to probe deeply into the earth and probe the upper portion for about 1 cm.
2. On the table is 2.5-9 numerical, numerical 7 basic is neutral, the smaller the number shows that the greater the acidity, please adjust soil pH value according to plant varieties.
3. Please pay attention that insert electrodes without touching the stone, not too hard, otherwise easy to damage the electrode, clean electrode after use.

Uses:
Measures Moisture
Measure PH Levels
Measure Light Levels

1.test the soil PH value:
Before planting,it's the best to analysis the different part of soil.so as to ensure the soil samples are representative, and analyses if the pH value of the soil is suitable for the crops.
How to test the PH value ?
firstly pull the 5 cm soil in upside,and crush the soil until 15cm deep.and clear the organic impurity which
will effect the test result,such as leaves,roots,etc...
2.)saturated the soil with water,until the soil become slimy(It's better to use rain water or distilled water)
3).Press this instrument button to "PH"
4.)Clear the probe.
5.)insert the whole probe into the soil
6.)Read the test result 1 minute later,
7).After using it,please clear the probe.
2.Test the soil fertility
Enough fertility is necessary for harvest.

How to test the soil fertility ?
1.)firstly pull the 5 cm soil in upside,and crush the soil until 15cm deep.and clear the organic impurity which
will effect the test result,such as leaves,roots,etc...
2.)saturated the soil with water,until the soil become slimy(It's better to use rain water or distilled water)
3).Press this instrument button to "FERTILIZER"
4.)Clear the probe.
5.)insert the whole probe into the soil
6.)Read the test result 5 seconds later,
7)press the botton to "OFF"
8).After using it,please clear the probe.

Result analysis:
too little means you need to spread fertilizer
1. The fertilizers dissolved in water, then water combined with added nutrients to crops;
2. Plant or transplanting plant watering should be combined with three weeks after fertilization, and each month when watering plants do.

Ideal means ok.
Combining with the watering, fertilizing once a month

Too much means no need fertilizer currently.
1. Just watering;
2. You will plant to transplanting to the new soil;
3. For the plants in the greenhouse, should be a lot of water, dilute nutrient leaching too much;
4. Don't let any chemical fertilizer, but can be applied into the manure, compost, plant residues, etc.