TIMEWAVE IOT Smart Water Metering Made Easy with Our
LoRaWAN-Enabled Solution
The LXSY-TW type (LoRaWAN)
The IOT smart energy meter
Electricity meter operating instruction
1. OVERVIEW
The smart water meter of the Internet of Things is composed of dry
water meter base meter, electric ball valve, magnetic resistance
sensor, MCU, lithium sub-battery pack, LoRaWAN wireless
communication module, control circuit and other components. It
adopts the electromechanical separation structure design. It has
the advantages of long communication distance, large capacity, fast
and convenient installation, and long service life.
2. PRODUCT CHARACTERISTICS
l Split structure: the electronic units are relatively independent
of the base table.
l Accurate measurement: using non-contact electronic detection
logic and measurement accuracy of 10 liters to ensure the
mechanical and electrical consistency.
l It has the function of touch button wake-up and long press on the
button to immediately go online remote data transmission.
l It has an infrared communication interface, which can read and
set relevant parameters.
l It has various alarm functions: abnormal state, measurement
fault, abnormal battery voltage, abnormal valve, etc.
l LoRaWAN timing uploading function: automatically upload data at
set time points (once a day by default), and also receive and
execute valid instructions from the platform.
l Micro-power consumption design: Adopt 3.6V lithium sub-battery
pack (ER26500 + HPC1520), with dormant current <10uA.
l Clock calibration function: Automatic calibration function and
remote calibration function of platform after the water meter is
connected to the network
3. TECHNICAL INDICATORS
| Nominal caliber (mm) | 15 | 20 | 25 |
| Overload flow Q4(m3/h) | 3.1 | 5.0 | 7.8 |
| Commonly used flow Q3(m3/h) | 2.5 | 4.0 | 6.3 |
| R=Q3/Q1 | 100 (Dry Type) |
| Range ratio | Q2/Q1=1.6 Q4/Q3=1.25 |
| Pressure loss level | Δp ≦0.063M P a |
| Maximum allowable water pressure | ≦1.2MPa |
| temperature grade | T30/T90 |
| Flow characteristics | Comply with GB / T 778.1~3-2007 standard, accuracy level: level 2 |
| Maximum allowable error | The high area (Q2 Q Q4) is ± 2%, and the low area (Q1 Q <Q2) is
± 5% |
| Water meter type | Electronic remote transmission water meter with electronic device |
| design criteria | CJT224-2012 Electronic Remote Water ter |
| Communication mode | LoRaWAN:864-865MHz |
| quiescent current | <10uA |
| Communication current | Data collection and generating currents <50mA and peak current
<100mA |
| work environment | 0~ + 45℃ (cold water) 0~ + 90℃ (hot water) 0~95%RH |
| working voltage | 2.7～3.6 V |
| operative norm | GB/T 778-2018 |
4. LIVE OPERATION PROFILE
Under the normal state, the water meter will be automatically put
online once a day (settable). Through wireless communication, the
water meter data will be uploaded to the system platform, and the
relevant instructions of the system platform (parameter setting and
valve control, etc.) will be received and executed at the same
time.
There are touch buttons on the water meter housing. In the dormant
state of the water meter, touch the button area with your finger,
the red status light on the water meter will flash a little
(infrared interface area), the water meter is artificially awakened
and in the infrared communication state. If you continue to touch
the button (3 seconds), the red indicator of the water meter will
flash two times in a row, at this time the water meter will
immediately go online (connect to the platform), upload the current
data to the system platform and receive the instructions of the
platform. The water meter in the process of uploading data, the red
indicator will also flash many times in a row. After the meter data
is uploaded, it will immediately enter the sleep state (low-power
mode).
In order to prevent human malicious multiple triggers to go online
(loss of battery power), we specifically set the interval time of
button trigger line (5 minutes). That is, the interval time between
two consecutive trigger line must be more than 5 minutes. At the
same time, it is stipulated that the number of daily button trigger
on the line should less than 8 times (the infrared communication
setting instruction is not affected by the number).
When the valve is closed, long press and hold the trigger button
for the first time every month for 3 seconds, and the water meter
valve will open. The water meter valve will be opened to overdraft
using 3m³ water. When the overdrawn 3m³ water quantity is used up,
the water meter closes the valve automatically.
5. INSTALLATION SIZE
| Model | Nominal caliber (mm) | L (mm ) | B (mm ) | H (mm ) | Take over control | Nut |
| LX SY -15 | 15 | 165 | 100 | 140 | R1/2 | G3/4 |
| LX SY -20 | 20 | 195 | 100 | 140 | R3/4 | G1 |
| LX SY -25 | 25 | 225 | 100 | 140 | R1 | G11/4 |
6. PRECAUTIONS
l Water meters should be checked frequently to prevent water meter
leakage accidents.
l In winter, it is necessary to prevent the water meter from
freezing and bursting. Installing insulation measures to the water
meter when necessary.
l When the home is not occupied for a long time, should close the
valve in front of the table to prevent water leakage accidents.
l Water meter is a measuring product and shall not be destroyed.
Destroying water meter is an illegal action.
7. TRANSPORTATION AND STORAGE
Water meters must be transported and stored under the original
packaging conditions. Products shall not be severely impacted
during transportation and unpacking, and are transported and stored
in accordance with GB / T15464-1995 General Technical Conditions
for Instrument Packaging. The products shall be stored in the
warehouse and placed on the platform frame. The stacking height
shall not exceed five layers. No corrosive gases shall be present
in the stored environment.
8. WARRANTY PERIOD AND AFTER-SALES SERVICE
If the user complies with the transportation, storage and
installation operation specifications, and the lead seal of the
manufacturer is still complete.If there is a quality problem, our
company is responsible for free repair or replacement within 18
months from the date of delivery the electricity meter.
During the whole life cycle of the products, our company implements
"three guarantees" for all electricity meter products, providing
necessary maintenance and services. Providing equipment wiring
diagram and necessary technical documents and drawings. According
to the requirements of users, provide necessary training for
maintenance personnel and operators. Providing training materials,
and update the software regularly and provide free upgrade.
After receiving the service request of the product user, our
company will respond within 12 hours.
